Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: 1972RedNeck
Showing results 1 to 15 of 499
Search took 0.36 seconds.
05-25-2019, 08:47 PM
Replies: 11
Views: 1,044
Posted By 1972RedNeck

Restore the body, mod the heck out of the...

Restore the body, mod the heck out of the drivetrain.
04-16-2019, 07:57 AM
Replies: 3
Views: 386
Posted By 1972RedNeck

Yes, I heard of that movie years ago when I was...

Yes, I heard of that movie years ago when I was first researching delay wipers but never got around to watching it as I don't have television. Sounds like he wasn't used to business ethics and didn't...
04-14-2019, 09:12 PM
Replies: 3
Views: 386
Posted By 1972RedNeck

Delay Wiper Upgrade Update

5 or so years ago I pulled the wiper switch and governor out of an '89 F350 for my '66. The wiring was plug and play with my existing wiper motor. Over the past few years the delay wipers have worked...
03-16-2019, 02:29 PM
Replies: 10
Views: 474
Posted By 1972RedNeck

From what I have found you cannot just swap the...

From what I have found you cannot just swap the top cover - you need the shifter "cane" as well. At least for an F250 4x4 or F350...
02-26-2019, 10:48 PM
Replies: 40
Views: 1,757
Posted By 1972RedNeck

Yes, yes it would if the check ball has a good...

Yes, yes it would if the check ball has a good seal.

The system would actually be more efficient if the bellows and line were filled with liquid as you would get more of a "true" displacement by...
02-23-2019, 08:14 PM
Replies: 40
Views: 1,757
Posted By 1972RedNeck

Any fluid that drains back from the nozzles goes...

Any fluid that drains back from the nozzles goes into the "T". It looks to me like the path of least resistance from the "T" would be into the bag, not the bellows.
02-20-2019, 07:14 PM
Replies: 40
Views: 1,757
Posted By 1972RedNeck

If it were to try to siphon, air would be pulled...

If it were to try to siphon, air would be pulled from the nozzles first.
02-20-2019, 07:11 PM
Replies: 40
Views: 1,757
Posted By 1972RedNeck

When it gets a hole in it, chances are, it will...

When it gets a hole in it, chances are, it will not "push" and "pull" the exact same volume each cycle. If the hole is such that it causes the bellows to "pull" just a little more than it "pushes",...
02-19-2019, 10:54 PM
Replies: 40
Views: 1,757
Posted By 1972RedNeck

The youngest of the young Slick aesthetes will...

The youngest of the young Slick aesthetes will have to step in for a quick physics and Fords lesson.

I am going to have to side with Chad on this one although he is either slightly off on a point...
02-19-2019, 09:08 PM
Replies: 8
Views: 415
Posted By 1972RedNeck

Personally, if you are just looking for a little...

Personally, if you are just looking for a little more oomph, I would try and source a 262 - they will mop the floor with a stock mid '70's 300 ('60's 300 would probably run close).

If you're going...
02-17-2019, 10:32 PM
Replies: 711
Views: 113,992
Posted By 1972RedNeck

So let me get this strait - someone got their...

So let me get this strait - someone got their feelings hurt because you italicized the word "false"? Furthermore, the site rules are very specific that italicizing such a word is "yelling" at someone...
01-20-2019, 05:03 PM
Replies: 4
Views: 414
Posted By 1972RedNeck

https://www.tomsbroncoparts.com/product/heater-blo...

https://www.tomsbroncoparts.com/product/heater-blower-motorsquirrel-cage-upgrade-kit-super-high-flow

This one? My blower motor has been making some noise and I have been looking for an alternative...
01-16-2019, 08:22 PM
Replies: 20
Views: 2,624
Posted By 1972RedNeck

Negative. Large opening pickup fenders are WAY...

Negative. Large opening pickup fenders are WAY smaller than F600 fenders.
01-16-2019, 08:00 PM
Replies: 16
Views: 716
Posted By 1972RedNeck

I assume you run about 29" tires? 3.25 with...

I assume you run about 29" tires?

3.25 with the .85 overdrive comes out to be 2.76:1 overall. Running 70, you should be turning about 2200 RPM correct?

I think I have read where Bill (Number...
01-16-2019, 07:56 PM
Replies: 16
Views: 716
Posted By 1972RedNeck

Peak efficiency is typically very near peak...

Peak efficiency is typically very near peak torque (RPM wise).

Typical FE will hit peak torque around 2200 - 2400. Set it up so you are running 2200 ish @ 70 in a 2 wheel drive pickup and you will...
Showing results 1 to 15 of 499
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.