Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: dmack91
Showing results 1 to 15 of 500
Search took 0.28 seconds.
03-20-2017, 11:32 PM
Replies: 15
Views: 2,480
Posted By dmack91

After searching a wrecking yard, I found a set od...

After searching a wrecking yard, I found a set od seat brackets,from an early 2000 Chrysler t&c van's drivers seat worked perfectly on the bench I used.
01-28-2017, 10:53 PM
Replies: 3
Views: 766
Posted By dmack91

Wheel offsets will affect what tire you can fit. ...

Wheel offsets will affect what tire you can fit. I have stock suspension and with 15x7 zero offset wheels, I am running 275/60/15 on the rear and 255/60/15 on the front.
01-11-2017, 08:15 PM
Replies: 10
Views: 954
Posted By dmack91

Like Dave said, Watch for steering box clearance....

Like Dave said, Watch for steering box clearance. I used a 289 and a Toyota ps box. Wish I had offset the engine to the passenger side an inch or so for extra exhaust clearance. Also watch for fan...
12-27-2016, 10:41 PM
Replies: 18
Views: 1,095
Posted By dmack91

Mine wasn't seized at the upper pivot, but at the...

Mine wasn't seized at the upper pivot, but at the lower where the nut and spring are. One solid mass of rust.

I cleaned it up with a wire brush and heated the seized nut up red hot with an...
11-20-2016, 08:21 PM
Replies: 134
Views: 13,620
Posted By dmack91

Nice parts find. Should save you some time.

Nice parts find. Should save you some time.
11-15-2016, 05:44 PM
Replies: 7
Views: 2,702
Posted By dmack91

When I tried to pull the pitman arms off the...

When I tried to pull the pitman arms off the toyota ps boxes I picked up for mine, they wouldn't budge even with a puller. As I wasn't going to reuse the old arm, I used an angle grinder with a...
11-14-2016, 11:23 PM
Replies: 12
Views: 1,677
Posted By dmack91

[QUOTE=pweng1;16679207]I am going thru the same...

[QUOTE=pweng1;16679207]I am going thru the same thing right now.As I can see it mounts with side mount bolt heads just about an inch higher than frame and center of mounts about 11 inches aft of...
11-13-2016, 11:51 PM
Replies: 215
Views: 9,916
Posted By dmack91

Been driving my 50 for a few years now. Current...

Been driving my 50 for a few years now. Current project is a 1968 Chevelle for my wife (and repairing other people's rigs), so haven't been doing much on the F1. Do miss the forum - too many other...
11-13-2016, 12:01 AM
Replies: 4
Views: 612
Posted By dmack91

Unfortunately, the salt air tends to make old...

Unfortunately, the salt air tends to make old vehicles a rare sight there. I think they also have inspections on vehicles.
11-11-2016, 04:25 PM
Replies: 1
Views: 342
Posted By dmack91

Looks like: 9 = 1949 7H = six cylinder ...

Looks like:

9 = 1949
7H = six cylinder
C= 1/2 ton
Reminding digits are the production number
06-18-2015, 01:03 AM
Replies: 20
Views: 1,996
Posted By dmack91

Looks great Ryan!!

Looks great Ryan!!
06-04-2015, 09:43 PM
Replies: 7
Views: 1,638
Posted By dmack91

I too used it on most joints. It cleans up any...

I too used it on most joints. It cleans up any inconsistencies and hopefully eliminates rubbing through paint (cause rust runs ).
03-02-2015, 02:50 AM
Replies: 18
Views: 2,063
Posted By dmack91

While your gap does look a bit wide, the fender...

While your gap does look a bit wide, the fender to cowl seal will take care of most of it. You do not need additional welting in that joint.


On the fender to running board area, they should fit...
02-23-2015, 04:43 AM
Replies: 1
Views: 4,963
Posted By dmack91

Not sure how you are going to get a title in...

Not sure how you are going to get a title in Oregon with only a bill of sale. Prob why he is letting it go cheap.
02-22-2015, 11:40 AM
Replies: 11
Views: 548
Posted By dmack91

I guess I went with the easy solution. I made a...

I guess I went with the easy solution. I made a stop from angle iron with a gusset and adjusted it so that it would stop the pitman arm from moving far enough to contact the tire. Didn't really...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.