Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: lvin4jc
Showing results 1 to 15 of 500
Search took 0.39 seconds.
07-19-2018, 11:54 PM
Replies: 5
Views: 366
Posted By lvin4jc

The Crown Vic is a tank, I wouldn't hesitate...

The Crown Vic is a tank, I wouldn't hesitate about that kind of mileage. Of course, my daily driver pickup has 542,xxx miles on it and runs perfectly so maybe i'm biased.

Anyway, are you...
07-10-2018, 12:29 PM
Replies: 1
Views: 235
Posted By lvin4jc

What parts can I steal for my 69 out of a 82 e150?

My 69 has a 351w out of a 1979 in it. I have a 1982 e150 351 that I got cheap, runs fine but the van body is gross and the tank needs cleaned out.

I'm wondering if I could steal;
power steering...
11-09-2017, 10:41 PM
Replies: 21
Views: 6,845
Posted By lvin4jc

Wanted to drop by and wrap this thread up and...

Wanted to drop by and wrap this thread up and hopefully help someone out in the future.

#1. The engine side pivot stud for a 302 fits perfectly into my 1978 351W. The boss is there (pictured...
10-30-2017, 05:53 PM
Replies: 21
Views: 6,845
Posted By lvin4jc

Well... Bill... That probably explains why I...

Well... Bill... That probably explains why I can't find one. Thanks for saving me from having to keep looking :-X22

That being said, in your diagram it looks like the bellhousing bracket would...
10-30-2017, 02:13 PM
Replies: 21
Views: 6,845
Posted By lvin4jc

I snapped some pictures, they do look like...

I snapped some pictures, they do look like they're in the same spot, however, the old stud is too large for the 351w hole. Can cast iron be drilled and tapped for the larger stud? Obviously I would...
10-29-2017, 03:41 PM
Replies: 21
Views: 6,845
Posted By lvin4jc

I'm not sure of that. The "boss" looks to be in...

I'm not sure of that. The "boss" looks to be in the same position on both blocks but I have not set the new engine down in the truck yet to verify that.

Any idea how to look up "block side of the...
10-29-2017, 01:57 PM
Replies: 21
Views: 6,845
Posted By lvin4jc

Would this work? - 1965-1973 Shift Mounting Plate...

Would this work? - 1965-1973 Shift Mounting Plate Kit - Cal Pony Cars (http://calponycars.com/1964-1973-classic/763-tra-653-555.html)


All helpful responses guys, I really appreciate it!
10-29-2017, 01:10 AM
Replies: 21
Views: 6,845
Posted By lvin4jc

I'm not against keeping the Z-bar. But since this...

I'm not against keeping the Z-bar. But since this truck had a 6cyl (single exhaust on pass. side) I'm not sure where the driver's side exhaust would go. I know that plenty of these trucks had V8's,...
10-29-2017, 01:06 AM
Replies: 21
Views: 6,845
Posted By lvin4jc

Part# 7A535 above is screwed into a boss in the...

Part# 7A535 above is screwed into a boss in the block on my 240. It looks like that "Boss" is much larger on the 1969 240 block than the 1978 351W block. Suggestions?
10-28-2017, 12:28 AM
Replies: 21
Views: 6,845
Posted By lvin4jc

Looking at a different clutch linkage, what do you recommend?

I'm putting a different engine in my '69 f100. The new engine has a different boss on the block where the Z-bar clutch linkage would go. My linkage is very worn out anyway and with the new engine...
Replies: 2
Views: 707
Posted By lvin4jc

Swapping 351W into '69 with Borg Warner T-18, which clutch???

I'm putting a 1978 351W into a 1969 F100 2wd with a Borg Warner T-18 4 speed manual. The truck currently has a 240 6cyl.

I bought a new flywheel, it is NAPA part number NCF88116.

So now I have...
10-03-2017, 11:08 PM
Replies: 3
Views: 194
Posted By lvin4jc

Thanks guys, I did get some from a guy in...

Thanks guys, I did get some from a guy in Mississippi. Twinzilla, you should sell yours on eBay, they bring about $150 shipped on there 0_o
09-25-2017, 07:46 PM
Replies: 3
Views: 194
Posted By lvin4jc

WTB: Engine perches/towers for 302/351 out of Dentside/bumpside

Needing 2wd engine perches out of a 1969-1978 Ford pickup that had a sbf in it. Thanks!
Replies: 13
Views: 1,145
Posted By lvin4jc

Where's a good place to buy new flywheels? The...

Where's a good place to buy new flywheels? The normal parts houses don't seem to have any :-X16
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.