Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: 1966Tbird
Showing results 1 to 15 of 500
Search took 0.52 seconds.
11-04-2012, 01:07 PM
Replies: 6
Views: 512
Posted By 1966Tbird

get a dremel tool and go under the truck and cut...

get a dremel tool and go under the truck and cut the detent plate so you don't have to pull it to the side to get to 4lo that's what i did
11-04-2012, 12:56 PM
Replies: 57
Views: 5,313
Posted By 1966Tbird

don't waste your time with a smallblock, all of...

don't waste your time with a smallblock, all of the parts for a 460 or a 351 cost roughly the same and the 460 will make better power and torque. I've got a 347 in my truck with tfs heads blah blah...
10-17-2012, 04:41 PM
Replies: 2
Views: 398
Posted By 1966Tbird

I had a setup like that drawing through the top...

I had a setup like that drawing through the top with an aeromotive pump (150gph) and it didn't work kept running out of fuel at high rpms, starts to go lean at 4k. Had it on a dyno and fuel pressure...
10-16-2012, 12:33 PM
Replies: 2
Views: 398
Posted By 1966Tbird

Modify Fuel Pickup to -8an Size

Has anybody modified their fuel pump pickup to a -8an size (1/2in)?

I am having fuel delivery problems and have a -6an line going from the pickup line on the tank to the fuel pressure regulator...
10-16-2012, 08:56 AM
Replies: 5
Views: 343
Posted By 1966Tbird

a flat tappet cam uses a cast gear and a roller...

a flat tappet cam uses a cast gear and a roller cam uses a steel gear, do not use the wrong gear or you will either eat the gear on the cam or eat the gear on the distributor and send metal all...
10-07-2012, 12:17 PM
Replies: 9
Views: 515
Posted By 1966Tbird

LIf you want to swap a 2wd c6 to a 4x4 you either...

LIf you want to swap a 2wd c6 to a 4x4 you either have to run a divorced transfer case or swap the output shaft to a 4x4 one and get the 4x4 tail housing for it (easier to just buy a junk 4x4 c6 and...
10-07-2012, 11:56 AM
Replies: 37
Views: 2,596
Posted By 1966Tbird

Yes but if you do it right you end up with a good...

Yes but if you do it right you end up with a good intake and carb that will support more power and give you more leeway for modifications with out having to go to someone to tune it for you.

What...
10-06-2012, 12:16 PM
Replies: 37
Views: 2,596
Posted By 1966Tbird

if you do a search (am i allowed to say that?...

if you do a search (am i allowed to say that? this isn't pirate) you will find numerous threads on how to convert your truck to a carb it's really simple as long as you don't have an e4od, get a...
10-01-2012, 10:15 PM
Replies: 4
Views: 482
Posted By 1966Tbird

I'm from west grove but I currently reside in...

I'm from west grove but I currently reside in Williamsport PA
10-01-2012, 02:01 PM
Replies: 61
Views: 6,272
Posted By 1966Tbird

you should have 12v at each injector from the...

you should have 12v at each injector from the power wire on the injector to battery ground since the computer uses a ground side switch to fire the injectors
10-01-2012, 01:37 PM
Replies: 4
Views: 482
Posted By 1966Tbird

Video of my 349w Cammin

I know this isn't a tech thread but I wanted to show off my junk.
89 f-150
349ci windsor trickflow 190cc heads
.598 lift hr cam with comp pushrods and pro gold rocker arms
air gap intake
750...
09-24-2012, 01:19 PM
Replies: 4
Views: 970
Posted By 1966Tbird

decided to quit *ucking around with it and just...

decided to quit *ucking around with it and just put in a walbro 255 pump and sell my shiny aeromotive pump to someone who has a sumped tank with a fitting on the bottom so it is truely gravity fed...
09-24-2012, 04:23 AM
Replies: 23
Views: 1,755
Posted By 1966Tbird

What you need to do is get a carbed manifold of...

What you need to do is get a carbed manifold of your choice and a 4bbl carb of your choice you will also new a distributor of your choice and a bypass fuel pressure regulator, Russell makes special...
09-23-2012, 10:37 AM
Replies: 4
Views: 970
Posted By 1966Tbird

I was thinking that I could take a factory in...

I was thinking that I could take a factory in tank pump and put it in the tank to feed the aeromotive pump, would that create a restriction?
09-22-2012, 02:03 PM
Replies: 15
Views: 12,532
Posted By 1966Tbird

mine has been spun to 7500 with muddy water in...

mine has been spun to 7500 with muddy water in it, tractor hydraulic oil, engine oil, power steering fluid, atf pretty much anything you can think of, one of my lines has a leak so I am constantly...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.