Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: fairlane68
Showing results 1 to 15 of 333
Search took 0.44 seconds.
07-31-2011, 02:01 PM
Replies: 18
Views: 20,640
Posted By fairlane68

I cleaned that when I had the throttle body off.

I cleaned that when I had the throttle body off.
07-31-2011, 01:19 PM
Replies: 18
Views: 20,640
Posted By fairlane68

I missed that. I did disconnect all vacuum...

I missed that.

I did disconnect all vacuum lines from the engine except for the MAP sensor, with no change in symptoms. I guess the next step is to pull the valve covers and watch the valves for...
07-30-2011, 03:47 PM
Replies: 18
Views: 20,640
Posted By fairlane68

Nah..."out of range" means it couldn't be tested...

Nah..."out of range" means it couldn't be tested because it was cold, or below operating temperature, which it was. If it were to spit that out with a hot engine, then yeah, that would be my problem.
07-30-2011, 02:52 PM
Replies: 18
Views: 20,640
Posted By fairlane68

It spit out some codes, something it's never...

It spit out some codes, something it's never done. 113, 118, 126...all for the ACT and ECT being out of range (cooled down engine), but I got a 327 DPFE/EVP below .2V. I'll mess with it more...
07-30-2011, 01:59 PM
Replies: 18
Views: 20,640
Posted By fairlane68

No, I don't have any cracked vacuum lines,...

No, I don't have any cracked vacuum lines, rubber, plastic, or otherwise, none that I can see.
07-30-2011, 01:18 PM
Replies: 18
Views: 20,640
Posted By fairlane68

I cleaned the PCV last week whn I had the upper...

I cleaned the PCV last week whn I had the upper intake off. It was fairly clean, but I cleaned it anyway just to be sure. I'll check that ACT sensor. Do you know the resistance specs on it?
07-30-2011, 12:44 PM
Replies: 18
Views: 20,640
Posted By fairlane68

I'm checking the right one. The resistance was...

I'm checking the right one. The resistance was off compared to a new one, but it didn't fix the problem. Ignition timing is right at 10 degrees, where it should be. I'm two steps away from...
07-30-2011, 11:20 AM
Replies: 18
Views: 20,640
Posted By fairlane68

Good guess...and I think you may be right. I...

Good guess...and I think you may be right. I just checked the resistance on it and got nothing, indicating an open. It's a $20 gamble.
07-30-2011, 10:59 AM
Replies: 18
Views: 20,640
Posted By fairlane68

94 Bronco 5.8L driveability problem...stumped.

I need some help with this one...

My Bronco is having a cold idle problem that has had me stumped for some time, and I'm tired of chasing it. WHen the engine is below operating temp, it runs like...
07-12-2011, 02:39 PM
Replies: 16
Views: 6,139
Posted By fairlane68

Reid Racing makes them. They make them for Ford...

Reid Racing makes them. They make them for Ford and Chevy axles, D44's and D60's. Already have them on the parts list! :-X22
07-10-2011, 07:03 PM
Replies: 16
Views: 6,139
Posted By fairlane68

I thought about that, but this is a steering part...

I thought about that, but this is a steering part on a truck that will end up weighing close to 5000 lbs, and towing a race car. Also, I don't have that kind of confidence in my local machine shop...
07-09-2011, 10:26 PM
Replies: 16
Views: 6,139
Posted By fairlane68

The three holes where the steering arm bolts to...

The three holes where the steering arm bolts to the knuckle are warped beyone repair, and everything else is missing. If it wasn't for that, all I would need would be the caliper mount brackets. ...
07-08-2011, 12:08 PM
Replies: 16
Views: 6,139
Posted By fairlane68

I was referring to using the knuckles out. They...

I was referring to using the knuckles out. They can be used.

I have a bare 79 F-250 D44 HD, but as luck would have it, the knuckles are bad. What is the difference between the 78-79 D44 HD's and...
07-07-2011, 11:14 PM
Replies: 16
Views: 6,139
Posted By fairlane68

That's what I'm unclear on. I thought they did...

That's what I'm unclear on. I thought they did use 15's on the D44 HD axles, but the clearance was so close that you could shave off the wheel weights. This is what happens when you get old...you...
07-07-2011, 11:00 PM
Replies: 16
Views: 6,139
Posted By fairlane68

8-lug axles and 15" wheels

What years did Ford have 15" wheels on their 3/4 and 1 ton trucks? It was in the 70's wasn't it? I'm researching parts for a 3/4 ton axle swap for my Bronco, and I know I can use Chevy 8-lug D44...
Showing results 1 to 15 of 333
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.