Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: animator
Showing results 1 to 15 of 317
Search took 0.58 seconds.
Yesterday, 04:09 PM
Replies: 25
Views: 1,081
Posted By animator

Mine was 4-wheel drive already, so it made sense....

Mine was 4-wheel drive already, so it made sense. You'd be converting to a 4x4 setup with a solid axle, as the time, money, and effort to swap something solid that wasn't a drive axle would be...
Yesterday, 11:49 AM
Replies: 11
Views: 281
Posted By animator

It's easy enough to drop the tank. I've done it...

It's easy enough to drop the tank. I've done it by myself a couple times.

If there's gas in it, disconnect the line at the filter and jump the fuel pump to pump it out into a container. Once...
Yesterday, 10:50 AM
Replies: 25
Views: 1,081
Posted By animator

I'm not a welder, but am a weekend warrior...

I'm not a welder, but am a weekend warrior hobbyist and wouldn't have any problem with that setup. But by saying that, I'm sure the welding "experts" will all want to start a pissing match on how...
04-02-2019, 12:10 PM
Replies: 9
Views: 401
Posted By animator

Sounds like air in the system. Likely in the...

Sounds like air in the system. Likely in the master cylinder. Take it out, bench bleed it, and put it all back on, then bleed the line.
03-30-2019, 10:52 AM
Replies: 10
Views: 386
Posted By animator

I know you say you've checked ground, but when I...

I know you say you've checked ground, but when I first attempted mine, I had the same issue--I couldn't get it to go into calibration mode. I had my ground connected to a bolt under the dash, which...
03-21-2019, 12:51 PM
Replies: 9
Views: 375
Posted By animator

I bought a switch panel from Amazon, then made my...

I bought a switch panel from Amazon, then made my own mounting panel for it, and mounted it under the dash, just under the ash tray, directly above the shifter. Wired up all my lights, and even have...
03-18-2019, 12:56 PM
Replies: 12
Views: 4,805
Posted By animator

I left my dipstick tube in place, and just kinda...

I left my dipstick tube in place, and just kinda gently bent it out of the way when I replaced my lifter cover gasket, and bent it back into place once it was finished. .
03-08-2019, 04:51 PM
Replies: 5
Views: 327
Posted By animator

I can't see a reason why you can't do it that...

I can't see a reason why you can't do it that way.

Once the pan is down, unbolt the oil pickup and it can drop into the pan, just be sure to put it back before you bolt the pan back up :D
01-21-2019, 06:06 PM
Replies: 18
Views: 1,066
Posted By animator

Say whatever you want, but I know how a detroit...

Say whatever you want, but I know how a detroit locker works.
01-21-2019, 03:59 PM
Replies: 18
Views: 1,066
Posted By animator

Trust me, I get how my locker works. Under...

Trust me, I get how my locker works. Under power, the rear is locked. Yes there is some slack between sides, but not a whole lot. I'll chirp a tire turning from a stoplight or even backing out of...
01-20-2019, 06:13 PM
Replies: 18
Views: 1,066
Posted By animator

Biggest dangers occur when going around a curve,...

Biggest dangers occur when going around a curve, when the outer tire wants to turn faster than the inner tire. The locker, doing what it does, will force them to spin equally, so usually the inner...
01-20-2019, 06:06 PM
Replies: 8
Views: 545
Posted By animator

Replaced my sending unit with a Spectra brand...

Replaced my sending unit with a Spectra brand from the auto parts store. It ran fine for a few days, then started giving me low fuel pressure issues. I found a small bit of metal in the filter, so...
12-03-2018, 04:43 PM
Replies: 9
Views: 471
Posted By animator

Nope, I'll just take my 4runner... :) I...

Nope, I'll just take my 4runner... :)

I haven't checked for codes yet, but will when I get more time to mess with it. I'm not throwing a CEL right now, so I'm assuming there won't be any codes. ...
12-03-2018, 09:57 AM
Replies: 9
Views: 471
Posted By animator

Yes, it is submerged and picks up at the lowest...

Yes, it is submerged and picks up at the lowest point in the tank. I was thinking it could be a heat issue with the pump as well, but the thing that makes me question that is the fact it only...
12-02-2018, 11:07 AM
Replies: 9
Views: 471
Posted By animator

4.9l losing power at highway speed

Truck's a '93 with the 300 6cyl and a 5sp, all with around 230k miles.

After spending most of last spring/summer working on this truck getting it ready to be driven regularly after having sat for...
Showing results 1 to 15 of 317
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.