Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Aaron81
Showing results 1 to 15 of 84
Search took 0.03 seconds.
06-01-2019, 09:01 PM
Replies: 1
Views: 283
Posted By Aaron81

No one? ��

No one? ��
06-01-2019, 10:30 AM
Replies: 1
Views: 283
Posted By Aaron81

F 250 hood side Emblem

Anyone have a "FORD F-250" hood side emblem, for the 1954 (found on 1953 also)?

Standard style, no boomerang....
05-30-2019, 02:09 PM
Replies: 10
Views: 740
Posted By Aaron81

My Napa crossed referenced to their "crossfire...

My Napa crossed referenced to their "crossfire series" paint

They did call their service support to get the formula, crossing from Dupont I believe. Some reason I think you skip the "prefix" and...
05-17-2019, 02:02 PM
Replies: 9
Views: 730
Posted By Aaron81

7109 is a round wire "spring" that holds the 3...

7109 is a round wire "spring" that holds the 3 paws, pushes them outward. The 3 paws go on the outside of 7105. Then it slips into the 7106.

I re built my T87D just last fall with new blockers and...
04-22-2019, 05:08 PM
Replies: 6
Views: 367
Posted By Aaron81

midfifty.com reproduces to original, I think...

midfifty.com

reproduces to original, I think about $150

not sure who makes them for them?
04-22-2019, 08:35 AM
Replies: 6
Views: 367
Posted By Aaron81

Serial number on frame :)

I am sure some know this already, but did you know (at least on 1954) your frame is stamped with your serial number on the front cross member support (the one the front engine mount bolts to)

Just...
04-15-2019, 12:43 PM
Replies: 2
Views: 166
Posted By Aaron81

I didn't have ALL the applications, but there now...

I didn't have ALL the applications, but there now we have it. Thanks!
04-15-2019, 12:07 PM
Replies: 2
Views: 166
Posted By Aaron81

01T-4826 center bushing for F250 and F350

I located a good "soft" original 01T-4826 drive shaft support center bushing.

I looked forever to find one that was not hard as a rock and shrunk up. I have the ability to "clone" them and make...
04-14-2019, 03:34 PM
Replies: 12
Views: 654
Posted By Aaron81

Greg, your correct. The only way for the PTO...

Greg,
your correct. The only way for the PTO to spin backwards is if they ever made one with a "counter gear". It would need 3 gears in it. 1 gear used for forward and 2 gears used for backwards....
04-13-2019, 06:00 PM
Replies: 12
Views: 654
Posted By Aaron81

it is a single gear that pulls into the counter...

it is a single gear that pulls into the counter shaft gear.
04-13-2019, 05:29 PM
Replies: 12
Views: 654
Posted By Aaron81

makes sense.

makes sense.
04-13-2019, 05:24 PM
Replies: 12
Views: 654
Posted By Aaron81

interesting! So all the trucks that had dump...

interesting! So all the trucks that had dump beds, were express trucks, and someone added the bed and hydraulics?
04-13-2019, 05:22 PM
Replies: 12
Views: 654
Posted By Aaron81

in and out only.

in and out only.
03-22-2019, 08:54 PM
Replies: 15
Views: 613
Posted By Aaron81

tried already, the timken base line circle is the...

tried already, the timken base line circle is the same (bore) but the 4 bolt center line diameter/radius is not.
03-22-2019, 10:39 AM
Replies: 15
Views: 613
Posted By Aaron81

Wheel bores I believe is the same. As you stated...

Wheel bores I believe is the same. As you stated with no eng degree, that is why I want to take the guess work out and put a very similar size drum back on the setup. stock was the 12 X 2, as to...
Showing results 1 to 15 of 84
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.