Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Fard
Showing results 1 to 15 of 60
Search took 0.46 seconds.
01-18-2015, 01:07 PM
Replies: 23
Views: 1,521
Posted By Fard

Lighten up man! It is not the end of the world if...

Lighten up man! It is not the end of the world if this doesn't work out. I am perfectly willing to accept defeat at any time. I don't care if I am better than anyone at anything, life's too short for...
01-17-2015, 12:19 PM
Replies: 23
Views: 1,521
Posted By Fard

I'll keep you updated when I get a chance to get...

I'll keep you updated when I get a chance to get into this a bit, I seem to think that the clockspring harness should not vary except for one extra wire that goes over to the ignition switch, and...
01-17-2015, 07:11 AM
Replies: 23
Views: 1,521
Posted By Fard

Thanks I will just have to see whats there, and...

Thanks I will just have to see whats there, and deal with it. I could just cut a piece of wood to stick between the gas pedal and dash? :)
01-16-2015, 06:33 PM
Replies: 23
Views: 1,521
Posted By Fard

If we have the 10 pin connector then would this...

If we have the 10 pin connector then would this not already have the right clockspring? I haven't looked yet, but if it is not the right one then what difference does it make if I have the plug or...
01-16-2015, 01:06 PM
Replies: 23
Views: 1,521
Posted By Fard

I think I will check into a new clockspring as...

I think I will check into a new clockspring as well. If it doesn't need it I won't do it! I kinda thought I might end up taking those down to the scrap man, but can use some of the drawers in my...
01-15-2015, 08:42 PM
Replies: 0
Views: 564
Posted By Fard

Weatherguard Van Setup out of 2000 E-250

Nice used Weatherguard 2 four drawer cabinets some have rubber tool pads,3 Steel cabinets with shelves also rubber pads, 2 Full height side shelf units, one with 16 drawer small parts unit, also have...
01-15-2015, 08:33 PM
Replies: 23
Views: 1,521
Posted By Fard

YES! I am aware of the air bag procedure! Isn't...

YES! I am aware of the air bag procedure! Isn't there a brake switch off the master cylinder for this as well? I think my old van had that and I did not see one on my new old van. By the way this van...
01-15-2015, 08:30 AM
Replies: 23
Views: 1,521
Posted By Fard

JWA, So I am lookin for the cable bracket that...

JWA, So I am lookin for the cable bracket that may or may not be on the throttle body for the cruise, then change over my steering wheel and insert 10 pin plug and mount cruise unit? Also get a fuse...
01-14-2015, 12:20 PM
Replies: 23
Views: 1,521
Posted By Fard

I couldn't find a van with power windows, but...

I couldn't find a van with power windows, but would sure like at least one on drivers side, do I need ford harness for that too? Or do a aftermarket, that window crank is so low to reach.
01-14-2015, 09:47 AM
Replies: 23
Views: 1,521
Posted By Fard

I found a 2000 pristene body with 72,000 original...

I found a 2000 pristene body with 72,000 original miles 5.4 w/ R470W tranny, (I have a fresh transmission to drop in when needed plus many other new parts off my 99 van. The only problem is , this...
01-13-2015, 09:41 AM
Replies: 23
Views: 1,521
Posted By Fard

I got my new old van and YES! It does in fact...

I got my new old van and YES! It does in fact have the coveted 10 pin connector. I am ready to do the swap. THX
12-06-2014, 04:30 PM
Replies: 23
Views: 1,521
Posted By Fard

Thanks man! I will take your advice, thanks for...

Thanks man! I will take your advice, thanks for the photos and all. You would think they'd a put the right wiring in from the jump, in all of them, but I bet Mr. Snoid sitting up in some office...
12-06-2014, 07:11 AM
Replies: 23
Views: 1,521
Posted By Fard

Cruise Control Swap

I have a rusty 99 van and have found a rust free 2000 e-250 that doesn't have cruise. I want to take my cruise out of the 99 and put it in the new van. I have the steering wheel w all switches and...
05-04-2014, 03:04 PM
Replies: 1
Views: 443
Posted By Fard

Upper Steering shaft bearing

I was having trouble with my steering having hard spots in it and just found out that I need new upper bearing for the steering shaft, I knew it had play, but i thought it was just loose bolts. ...
05-01-2014, 08:19 AM
Replies: 4
Views: 534
Posted By Fard

I wondered if that could be it, I don't have a...

I wondered if that could be it, I don't have a lathe, maybe I will get down there, It's a PITA with a straight edge and see what I can see. I could just get a new pulley, actually I read somewhere...
Showing results 1 to 15 of 60
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.