Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: iwlbcnu
Showing results 1 to 15 of 49
Search took 0.39 seconds.
12-18-2014, 06:24 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

I'm def in a better mood about it, no clue on...

I'm def in a better mood about it, no clue on it's future, It's odd, I like it, BUT already have way to many irons in the fire. Son is trying to claim it, but then he claims everything I own. Once...
12-17-2014, 06:18 PM
Replies: 46
Views: 5,175
Posted By iwlbcnu

Well I'll be!!! Pulled out several carbs and one...

Well I'll be!!! Pulled out several carbs and one had the same style Venturi, so I just swapped it and it purrs like a kitten. No clue what's up with the original, I ran a wire and blew all thru it...
12-17-2014, 06:43 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

I'm not a paid mech, but I have a lot of...

I'm not a paid mech, but I have a lot of motorized hobbies so not a newbie, and this has driven me nuts. I am big into early Broncos, so have a few 2100's laying around to try. The one on the truck...
12-16-2014, 07:13 PM
Replies: 46
Views: 5,175
Posted By iwlbcnu

No, irritated, lost interest and gave up for now....

No, irritated, lost interest and gave up for now. Going to rebuild another 2100 and try when I get time.
12-13-2014, 04:01 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

16 was at the lowest idle without stalling, no...

16 was at the lowest idle without stalling, no tach. As soon as I raised it any I had 18 and then 20.
No PVC, all original down draft.
Waiting for some more cycles to go Back thru, retorque heads...
12-12-2014, 08:55 PM
Replies: 46
Views: 5,175
Posted By iwlbcnu

I checked the pin count several times. I did...

I checked the pin count several times. I did unhook the vacuum advance and set timing to 5 and it seems to rev better and I can open the choke fully while reved, but still won't idle. I sprayed some...
12-12-2014, 07:18 PM
Replies: 46
Views: 5,175
Posted By iwlbcnu

Alright, vacuum is 16 inches at idle, and jumps...

Alright, vacuum is 16 inches at idle, and jumps to 20 if I raise idle slighly, it stays steady, no jumping.
Pulled the carb, ran wire thru every hole I could find, then blew thru it all, no clogs...
12-12-2014, 05:13 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

Tried again last night and ya'll have convinced...

Tried again last night and ya'll have convinced me it is in the carb, will be pulling it down tonight I hope. I took video, but can't get it to load to youtube to share it with you. Also going to tap...
12-11-2014, 12:56 PM
Replies: 46
Views: 5,175
Posted By iwlbcnu

Carb was soaked for several days in carb cleaner,...

Carb was soaked for several days in carb cleaner, and completely blown thru.
Replies: 1
Views: 671
Posted By iwlbcnu

Value of NOS 272 blocks?

Looks like my previous post was deleted, so I'll try here. Was visiting someone and they mentioned they had TWO NOS 272 blocks from back when, and would like to sell them. Any idea on what they would...
12-11-2014, 06:11 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

Can't see much, but here are engine shots. Hope...

Can't see much, but here are engine shots. Hope to find time this weekend to try it again.
...
12-10-2014, 10:56 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

I tried using a heater hose last night as someone...

I tried using a heater hose last night as someone else suggested, and heard nothing.
I really don't think it is a timing issue as from my experience if you are off much either way it won't run. But...
12-10-2014, 06:57 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

Dizzy, and wires were routed on the stand. I have...

Dizzy, and wires were routed on the stand. I have timing set at 6 advance right now. Truck fires right up, idles fine and can be driven, just the choke plate has to be almost closed. If you try to...
12-10-2014, 06:37 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

the Early 2100. No gauge, need to rig up a place...

the Early 2100. No gauge, need to rig up a place to hook one up.
12-10-2014, 06:21 AM
Replies: 46
Views: 5,175
Posted By iwlbcnu

292 vacuum leak, possible causes?

Okay, to move on from my previous thread, I had a few minutes to fool with it again last night. Back story, fresh rebuild, nothing fancy, but new rings, bearings, timing chain, heads checked and...
Showing results 1 to 15 of 49
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.