Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: f_ford_custom
Showing results 1 to 15 of 139
Search took 0.61 seconds.
11-08-2009, 11:06 PM
Replies: 8
Views: 1,020
Posted By f_ford_custom

I guess it is the lighting control module. Just...

I guess it is the lighting control module. Just found it. had to leave off the date code. It does control almost everything in the car, but now I know how to delete it.

Thank ye redneck.
...
11-08-2009, 10:38 PM
Replies: 8
Views: 1,020
Posted By f_ford_custom

no camera, but it has 4 connectors, 2 blades -...

no camera, but it has 4 connectors, 2 blades - black, 16 pin - grey, 22 pin - grey, 16 pin - white. positions clockwise starting @ 2. The 2 grey connectors are molded in 1 on the box
4.25 in...
11-08-2009, 10:14 PM
Replies: 8
Views: 1,020
Posted By f_ford_custom

no car phone, theres like 40 or so wires going to...

no car phone, theres like 40 or so wires going to and fro, the box is about the size of a childs shoe box, with vent slots all over it, it was next to the steering column.

everything runs through...
11-08-2009, 10:00 PM
Replies: 8
Views: 1,020
Posted By f_ford_custom

does anyone know what this is?

I am swapping the 4.6 out of a Merc GMQ. I was tracing down wires, and almost everything runs to this box under the dash. Ford PN: F7AB-13C788-AA
I know the car has an alarm, and I have the...
Replies: 26
Views: 4,968
Posted By f_ford_custom

Sorry to change subject back, but if you want to...

Sorry to change subject back, but if you want to check the timing chain, turn the crank to TDC, pull the dizzy cap, then see how far you have to move the crank in the opposite direction before the...
Replies: 8
Views: 428
Posted By f_ford_custom

How about the other wire, had 78 LTD, and red...

How about the other wire, had 78 LTD, and red plugged into white, white into red, one is ignition, one is Start. You don't have the yellow connector, do you, the extra sensor (early MAP) went out,...
Replies: 10
Views: 454
Posted By f_ford_custom

use tape measure, front/rear may work, have...

use tape measure, front/rear may work, have brandX half-ton w/ 1 ton axle in rear, just knocked out bolts, swaped axles, leafs and all, and rebolted. Of course, I wanted the heavier springs.
Replies: 1
Views: 224
Posted By f_ford_custom

fitment issues - maybe

Does anyone know if a 5.8/aod will physically fit in a 4/4spd 86 Mustang? I know I will need a driveshaft, mounts, headers, oil pan/pickup...shifter. I have several to choose from, 86-93. What...
Replies: 10
Views: 454
Posted By f_ford_custom

all engine parts out of the question, 351M = 351C...

all engine parts out of the question, 351M = 351C = 429/460 bellhousing, and 351W = 302. If same # of lugs, wheels/tires will interchange. cannot remember small parts, sorry.
Forum: Bronco II
11-02-2008, 08:06 PM
Replies: 19
Views: 24,088
Posted By f_ford_custom

Just a suggestion, follow big rigs for a week, if...

Just a suggestion, follow big rigs for a week, if you are taking off faster than them, you can save 15-20% of your fuel if your acceleration matches theirs. As a truck driver, I will ask that as you...
09-02-2008, 12:47 PM
Replies: 3
Views: 1,787
Posted By f_ford_custom

thanks six, just finished a thorough exam...

thanks six, just finished a thorough exam yesterday, all is not well, head gasket is failing, needs suspension and tranny rebuild. have 97 GMQ parts car, 4.6/auto, thinking of doubling engine size,...
08-24-2008, 03:52 PM
Replies: 3
Views: 1,787
Posted By f_ford_custom

85 Mustang 2.3l OHC

Hi Y'all,

a few weeks ago (5-6-14 months?) I found an old HotRod Mag article on opening up the 2.3l, now I cannot find it again. I remember header-found for $181, intake and carb. They used like...
07-14-2008, 11:25 PM
Replies: 3
Views: 3,875
Posted By f_ford_custom

?89? DIS, right? Dual plug? you'll have to...

?89? DIS, right? Dual plug? you'll have to look for a ?88? or later block. Cam/crank sensor, dizzy hole, ?balancer shaft-its in a 96?. if you have to go to a different block, try a 83-(86 for...
Replies: 6
Views: 306
Posted By f_ford_custom

Thanks y'all, do you think it would help the...

Thanks y'all, do you think it would help the engine breathe with 1.7 rockers on the exhaust side? Not sure, but just thinking, needs valve cover gaskets anyway. Don't have money for headers/exhaust...
Replies: 21
Views: 1,459
Posted By f_ford_custom

The instructions will give you step-by-step...

The instructions will give you step-by-step instructions, but basicly just take off the dizzy cap/rotor, and the springs are right there on top. The insrtuctions will also tell what colors will come...
Showing results 1 to 15 of 139
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.