Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: CharlieLed
Showing results 1 to 15 of 500
Search took 0.52 seconds.
02-20-2019, 10:15 AM
Replies: 30
Views: 1,299
Posted By CharlieLed

Welcome to the FTE family...good start on the 56,...

Welcome to the FTE family...good start on the 56, making it your own is always the fun part of the project!
02-18-2019, 09:19 PM
Replies: 2
Views: 264
Posted By CharlieLed

Your taillight bulb has two filaments, one for...

Your taillight bulb has two filaments, one for the brake and one for the running light. Both of these filaments are grounded through the base of the bulb. When you apply voltage to either of these...
02-13-2019, 02:21 PM
Replies: 8
Views: 903
Posted By CharlieLed

I have never purchased a patch panel for the gas...

I have never purchased a patch panel for the gas filler but I have used many cab corner repair panels and just cut out the section I needed. Many jobs only need the lower cab corner section so the...
02-10-2019, 02:53 PM
Replies: 16
Views: 902
Posted By CharlieLed

Anything that I will tow I own...in fact, I don't...

Anything that I will tow I own...in fact, I don't think that there are any mom & pop rental places around any longer. The last place said that the Peoples Republic of Kalifornia was driving them out...
02-10-2019, 11:51 AM
Replies: 16
Views: 902
Posted By CharlieLed

Thanks Bobby...I'll check that out.

Thanks Bobby...I'll check that out.
02-10-2019, 09:37 AM
Replies: 7
Views: 351
Posted By CharlieLed

The glass should be inserted through the top...

The glass should be inserted through the top opening and dropped down on an angle. When then glass is inside the door then it is rotated, fit into the felt guides and lifted back up into the top...
02-10-2019, 09:25 AM
Replies: 16
Views: 902
Posted By CharlieLed

That is one issue that I have as well. Right now...

That is one issue that I have as well. Right now there is only one way to attach a trailer ball and that is on the bumper...if so I can see why it wouldn't handle a pull of over 2000 lbs. The...
02-10-2019, 09:12 AM
Replies: 7
Views: 615
Posted By CharlieLed

For the backsides of those grille bars I would...

For the backsides of those grille bars I would use a wire brush or wheel to remove the scaling and then treat with KBS Rust Blaster followed by a couple of coats of KBS Rust Seal. I use this...
02-08-2019, 10:24 PM
Replies: 16
Views: 902
Posted By CharlieLed

This has the Magnum 5.9 with 3.93 posi rearend....

This has the Magnum 5.9 with 3.93 posi rearend. PO ordered it with all available options. The wife already has her eye on it though since it is easier to drive/park than the 2500HD long bed that is...
02-08-2019, 09:55 PM
Replies: 16
Views: 902
Posted By CharlieLed

O/T New Hot Rod Truck in the Barn

Just bought this 2000 Dodge Dakota R/T from the neighbor, he has had it since new. Never been out of the San Diego area, 77K on the clock. Not a Ford but it is a hoot to drive.
...
02-08-2019, 09:35 PM
Replies: 7
Views: 308
Posted By CharlieLed

Here is a friend's truck...only one that I have...

Here is a friend's truck...only one that I have seen with metal inserts in the door panels and seats. Just another idea...
...
02-06-2019, 07:10 PM
Replies: 10
Views: 571
Posted By CharlieLed

The girlfriend (years ago...many years ago) had a...

The girlfriend (years ago...many years ago) had a Rambler that had a brake light problem. The brake light switch was a pressure type but it screwed in to the underside of the master cylinder where...
02-06-2019, 11:28 AM
Replies: 3
Views: 439
Posted By CharlieLed

The access openings work really well when...

The access openings work really well when cleaning out the lower cowl areas. Dirt and debris collect in these low areas, and with a little moisture added, rust and rot are soon to follow. Access...
02-05-2019, 12:08 PM
Replies: 19
Views: 922
Posted By CharlieLed

Henry Ford did not spend a dime on anything that...

Henry Ford did not spend a dime on anything that would not make him a dollar in return...paint on an undercarriage was a net loss and therefore not done.
02-05-2019, 12:04 PM
Replies: 28
Views: 15,290
Posted By CharlieLed

Back in the day there were the "Mitchell's...

Back in the day there were the "Mitchell's manuals"...these manuals had all the data/dimensions that a shop would need to straighten frames and align suspensions. Over the years this printed manual...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us About Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.