Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: F'n ford
Showing results 1 to 15 of 19
Search took 0.03 seconds.
Replies: 22
Views: 840
Posted By F'n ford

Thanks for helping! I still need to tune the carb...

Thanks for helping! I still need to tune the carb a little more to have it completely right.
Replies: 22
Views: 840
Posted By F'n ford

I would think they would be the same too. I...

I would think they would be the same too. I didn't check anything on the other distributor. I just pulled it and dropped the other one in. Guess something with that one if off. I'll look at it...
Replies: 22
Views: 840
Posted By F'n ford

FIXED!!! It ended up being the distributor...

FIXED!!!

It ended up being the distributor that came with the engine. I don't know if anything was wrong with it or if it was to do with it being from a 76 and my truck is a 84? I but my old one...
Replies: 22
Views: 840
Posted By F'n ford

I have a pressure gauge. I'll throw it on it...

I have a pressure gauge. I'll throw it on it tomorrow just to make sure. Gonna double check everything again before I pull the timing cover to see if they are out of time.
Replies: 22
Views: 840
Posted By F'n ford

It's is the initial takeoff. Once I'm going good...

It's is the initial takeoff. Once I'm going good in second it runs great. If I can shift quick enough and keep the rpm's up in 3rd then i can run third out good too. But once I get into 4th it's...
Replies: 22
Views: 840
Posted By F'n ford

The other engine had a bearing go bad and chewed...

The other engine had a bearing go bad and chewed up the crank. It's all the same but the engine. I'm really starting to think the cam may be out of time. But the think will run like a scalded dog...
Replies: 22
Views: 840
Posted By F'n ford

I have my regulator set to 5 psi. It's...

I have my regulator set to 5 psi.

It's idling great and it revs great. But when you take off it is really sluggish and then it will take off. 2nd and 3rd gears are better than 4th. When I...
Replies: 22
Views: 840
Posted By F'n ford

I fiddled with it for a few hours last night. ...

I fiddled with it for a few hours last night. Nothing I did really helped any

when I have it setting on tdc on the compression stroke where should my distributor be pointing? And would it be...
Replies: 22
Views: 840
Posted By F'n ford

I'l look at it tonight when I get home. It' only...

I'l look at it tonight when I get home. It' only running thru the mechanical pump. I took the electric one off. I'm starting to think it' more to do with timing. Maybe it does need a little more...
Replies: 22
Views: 840
Posted By F'n ford

300 i6 acts like it's not getting enough fuel?

I just installed a rebuild 300 into my 84 f150. When it idles it is fine. When I give it gas in neutral or with the clutch in it revs great. But when I go to take off it just falls on its face, and...
Replies: 5
Views: 476
Posted By F'n ford

I got it fixed!! I replaced the slave because it...

I got it fixed!! I replaced the slave because it was leaking. But I still was not getting enough movement from the slave to release the clutch. So I pulled off the master and the slave together and...
Replies: 5
Views: 476
Posted By F'n ford

Mine is external. What way do you turn the rod...

Mine is external. What way do you turn the rod that connects to the clutch for adjustments
Replies: 5
Views: 476
Posted By F'n ford

Clutch problems

Have a 1984 f150 with 300 i6 and np435 tranny. My clutch was slipping and it was hard to get into gear sometimes. Well I decided to change my clutch. I went with an 11 inch clutch. I got new...
Replies: 6
Views: 408
Posted By F'n ford

I have the pressure plate,clutch, and flywheel....

I have the pressure plate,clutch, and flywheel. The clutch came out of a 76 f series truck. I'm doing an engine swap. And the clutch was with the engine.

hate to sound ignorant, but what is the to...
Replies: 6
Views: 408
Posted By F'n ford

Throw out bearing

I'm going from a 10 inch clutch to a 11 inch. I got the clutch from someone, but it didn't have the throw out bearing with it. Is the bearing the same size for the 10 and 11 inch clutch? And it's a...
Showing results 1 to 15 of 19
 


 
Forum Jump

Contact Us About Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.