Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Fifty F3
Showing results 1 to 15 of 59
Search took 0.58 seconds.
06-04-2006, 10:08 PM
Replies: 81
Views: 2,576
Posted By Fifty F3

Punch cards and endless do loops. Two days...

Punch cards and endless do loops. Two days between input and output. And I had to get wireless because dial up was too slow!
05-01-2006, 04:03 PM
Replies: 8
Views: 481
Posted By Fifty F3

It's a relay, most likely for the horn. The...

It's a relay, most likely for the horn. The terminals should be marked "B" ,for battery, "S" for switch and "H" for horn.
04-23-2006, 09:33 AM
Replies: 84
Views: 4,010
Posted By Fifty F3

It's the same age I am. It's big, brutish,...

It's the same age I am.
It's big, brutish, cranky, slow to start, slow to get up to speed, and slow on the highway, kinda good looking in a homely sort of way and makes a fair bit of noise and...
04-22-2006, 06:09 AM
Replies: 34
Views: 850
Posted By Fifty F3

Talking Installed a pair of 4 inch speakers in the...

Installed a pair of 4 inch speakers in the speaker hole in the dash to go along with the modern radio and the six inchers in the doors. It's the only non stock item on the truck, other than the...
03-28-2006, 06:32 PM
Replies: 9
Views: 398
Posted By Fifty F3

There is a clip, and it's screwed to the firewall...

There is a clip, and it's screwed to the firewall about 6 inches above and about two inches to the left of the hole the cable comes in through.

Dave
03-27-2006, 10:35 AM
Replies: 2
Views: 319
Posted By Fifty F3

Talking Spring Has Sprung!!!!

Some of you may remember me asking last fall if it were preferable to remove the flathead 8 from my 1950 F3 with or without removing the front sheet metal. I have since taken the advice given, and...
02-09-2006, 09:40 AM
Replies: 2
Views: 284
Posted By Fifty F3

Just did it on my '50. Local (Canadian)...

Just did it on my '50. Local (Canadian) industrial rad shop sourced a core and sweated on the inlet and outlet for about $180 Cdn. I think I got worked over a bit, but am reasonably happy with the...
01-31-2006, 09:23 AM
Replies: 3
Views: 320
Posted By Fifty F3

Sorry, this won't help you much, but I've just...

Sorry, this won't help you much, but I've just pulled the original wiring harness out of my 1950 F3 and have mapped all the wires by gauge, original colour (yeah I'm Canadian), length and terminal...
12-04-2005, 05:39 AM
Replies: 53
Views: 1,743
Posted By Fifty F3

I pulled the engine out in mid October, had the...

I pulled the engine out in mid October, had the block cleaned and magnafluxed, the crank ground, and will, in a few minutes, go out into the attached garage where the kerosene heater will have...
12-01-2005, 11:30 AM
Replies: 8
Views: 562
Posted By Fifty F3

I'm guessin' that if we don't know where it is,...

I'm guessin' that if we don't know where it is, it's too far for him to deliver.
Dave
11-30-2005, 07:48 AM
Replies: 7
Views: 415
Posted By Fifty F3

I used a fixed 13/16" reamer and got a good close...

I used a fixed 13/16" reamer and got a good close fit.

Dave
11-26-2005, 07:38 AM
Replies: 312
Views: 18,276
Posted By Fifty F3

I'm Dave, 55 years old - same as my truck - and...

I'm Dave, 55 years old - same as my truck - and an Industrial Engineer. Will retire from managing a production machining plant in 20 (work) days.
11-14-2005, 02:48 PM
Replies: 22
Views: 1,012
Posted By Fifty F3

Mine's a fresh air heater, the name of which, I'm...

Mine's a fresh air heater, the name of which, I'm sure, was on the missing plate over the end of the blower motor shaft. It's identical to the ones discused here a few months ago, something Aire, I...
11-14-2005, 10:31 AM
Replies: 11
Views: 462
Posted By Fifty F3

THE best thing I did to my lumber wagon was to...

THE best thing I did to my lumber wagon was to mount (relatively) modern wheels and radials. You can almost drink coffee without wearing it now.
11-14-2005, 10:28 AM
Replies: 46
Views: 1,177
Posted By Fifty F3

Rings, rod, main and cam bearings, valves, guides...

Rings, rod, main and cam bearings, valves, guides and springs. Probably wiring it while the engine's out. May even open the transmission to scare the h___ out of myself.
Showing results 1 to 15 of 59
 


 
Forum Jump

Contact Us About Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.