Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Bubba Jones
Showing results 1 to 15 of 500
Search took 0.55 seconds.
08-18-2018, 04:21 PM
Replies: 10
Views: 832
Posted By Bubba Jones

I don't really have much insight on this but I...

I don't really have much insight on this but I assume it may be possible. I know you're not going this route, but to make a bronco with the coil sprung dana 44 be 8 lugs, it seems the easiest way is...
07-24-2018, 11:34 PM
Replies: 23,436
Views: 1,060,585
Posted By Bubba Jones

This is completely off topic but I'm surprised...

This is completely off topic but I'm surprised that this thread isn't on the first page. I don't check the forums every day, but almost every day and this thread is always there!

So I'll just say...
07-24-2018, 11:30 PM
Replies: 6
Views: 407
Posted By Bubba Jones

It wasn't too hard really. It was quite a bit of...

It wasn't too hard really. It was quite a bit of work, but not necessarily hard. The more tedious processes involved re pinning some wiring harnesses to get them to work properly with my Bronco...
07-24-2018, 11:21 PM
Replies: 323
Views: 14,685
Posted By Bubba Jones

Man I'm sorry to hear all the extra trouble......

Man I'm sorry to hear all the extra trouble... hopefully it can get fixed sooner. I wish I could do more than just wish you luck!
07-24-2018, 05:33 PM
Replies: 17
Views: 690
Posted By Bubba Jones

The part that was changed was the engine/injector...

The part that was changed was the engine/injector harness. It's not too big really, it plugs into the valve covers, glow plug relay, ICP, CPS, some other small sensors on the motor and the starter...
07-22-2018, 11:06 PM
Replies: 7
Views: 382
Posted By Bubba Jones

I have to say, the people on this forum are some...

I have to say, the people on this forum are some of the most helpful I've come across. Always willing to help and give information or help out with parts. It's nice to come across people helping each...
07-22-2018, 11:02 PM
Replies: 5
Views: 259
Posted By Bubba Jones

We'd need a little more information on the...

We'd need a little more information on the symptoms of wanting to overheat.

If it isn't actually overheating, and the temperature gauge is bouncing around a lot, it very well could be that you...
07-22-2018, 11:00 PM
Replies: 6
Views: 407
Posted By Bubba Jones

Taking out the instrument cluster is surprisingly...

Taking out the instrument cluster is surprisingly easy on these. Once it's out, taking off the plastic cover is super easy. You have to pry out the trim on the bezel with a screwdriver carefully,...
07-22-2018, 10:53 PM
Replies: 4
Views: 433
Posted By Bubba Jones

Well I would imagine the 460 would be close to a...

Well I would imagine the 460 would be close to a "direct" swap IF you grab the wiring harnesses from a donor vehicle (engine bay and under dash wiring harness.)

The 7.3 bolted directly in on the...
07-22-2018, 10:45 PM
Replies: 17
Views: 690
Posted By Bubba Jones

I changed out the wiring harness and went for a...

I changed out the wiring harness and went for a drive and have no problems! Because the problem was intermittent, I'm not 100% sure I fixed it, but I'm about 99% sure it's fixed. I've had this issue...
07-22-2018, 09:13 PM
Replies: 17
Views: 690
Posted By Bubba Jones

Finally got around to messing with the Bronco...

Finally got around to messing with the Bronco again this afternoon and I narrowed things down.

After a bunch of messing around, I decided to just start tugging on wires. When I tug on the wiring...
07-18-2018, 10:51 PM
Replies: 12
Views: 881
Posted By Bubba Jones

Yeah that may be worth doing. I don't know if...

Yeah that may be worth doing. I don't know if Cheyenne Wyoming has many places that would do that, but I'm nearby in Colorado I can find someone that will do that.

I haven't had much time to do...
07-17-2018, 08:38 PM
Replies: 12
Views: 881
Posted By Bubba Jones

I may look into that. I ended up using the stock...

I may look into that. I ended up using the stock y-pipe, and the cheap headers I purchased mate up to the stock y-pipe. However, because I cut the y-pipe into two sections, I welded it together a...
07-16-2018, 06:56 PM
Replies: 17
Views: 690
Posted By Bubba Jones

Yeah I was hoping so. It managed to start and...

Yeah I was hoping so. It managed to start and idle normally again, so I'm wondering if I just caught an air bubble in the HPOP system and got that out. However, it would constantly cut out under...
07-16-2018, 04:47 PM
Replies: 17
Views: 690
Posted By Bubba Jones

No change with the other IDM... it will kinda...

No change with the other IDM... it will kinda start, sometimes lug a bit, but stall out still.

Just changed the oil so oil is new and full. It has a "newer" melling LPOP on it so I don't think...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us About Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.