Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: projectnitemare
Showing results 1 to 15 of 499
Search took 0.55 seconds.
02-02-2019, 02:55 PM
Replies: 36
Views: 2,041
Posted By projectnitemare

It should still have the same 35 spline super 60....

It should still have the same 35 spline super 60. I've had a Spartan in the front of the last 2 trucks with no issues. I don't rock crawl but it had done the job when I needed it. It does cluck...
01-06-2019, 09:08 PM
Replies: 147
Views: 83,609
Posted By projectnitemare

Because of that original truck I never let any...

Because of that original truck I never let any parking brake release without my foot being on it.
01-06-2019, 09:05 PM
Replies: 2
Views: 224
Posted By projectnitemare

Not sure about the stamps at the abs senor but...

Not sure about the stamps at the abs senor but the N in the casting signifies that the housing is nodular iron. I don't recall any major physical difference until the 11-up. What you have should...
Forum: 6.2L V8
12-09-2018, 05:58 PM
Replies: 27
Views: 3,679
Posted By projectnitemare

I wasn't a huge fan. Getting rid of the drive by...

I wasn't a huge fan. Getting rid of the drive by wire lag was the improvement I liked. The initial purchase was to correct the speed for tires but it wouldn't do it. For the driving I did at the...
Replies: 15
Views: 768
Posted By projectnitemare

Best to pull the valvebody. The mention of RTV...

Best to pull the valvebody. The mention of RTV has bad news written all over it. If you are doubting your ability it would be time for a professional
11-12-2018, 09:22 PM
Replies: 19
Views: 1,149
Posted By projectnitemare

Just turned 59k this trip

Just turned 59k this trip
11-12-2018, 08:06 PM
Replies: 19
Views: 1,149
Posted By projectnitemare

DEF issues

On a trip today in my 16 F250, I'm suspecting a sensor going bad but not sure. I get a warning message 36 miles until limited to 50mph. I had filled and successfully reset the tank last week with...
11-10-2018, 07:58 AM
Replies: 2
Views: 274
Posted By projectnitemare

It will likely be a custom driveshaft. I'm sure...

It will likely be a custom driveshaft. I'm sure if all the planets align right just the rear section would work. On average, about 72 inches is max length for a one piece. That can vary due to...
Replies: 3
Views: 204
Posted By projectnitemare

When I did that for a living a few years back...

When I did that for a living a few years back parts for them were getting hard to find. I used VTP south for nearly all my parts. Look them up, they may be able to help you but you will like have...
10-13-2018, 08:43 AM
Replies: 6
Views: 524
Posted By projectnitemare

Now that the aftermarket is more involved gears...

Now that the aftermarket is more involved gears are easy to get. Be sure you are buying the 11-up 37 spline for the rear. I havent looked recently but the crush sleeve and inner pinion bearing used...
Forum: Offroad & 4x4
10-12-2018, 09:23 PM
Replies: 3
Views: 402
Posted By projectnitemare

You want the transmission output to be within a...

You want the transmission output to be within a degrrd of parallel to the axle input. With no engine load you may need a degree or so of correction to allow for spring wrap. Sounds like you are in...
09-30-2018, 08:09 PM
Replies: 9
Views: 368
Posted By projectnitemare

Get a set of extractors, not one. Craftsman...

Get a set of extractors, not one. Craftsman still may sell a set at a decent price. Yes you need to hammer the extractor on and it will bite into the bolt. Heat the housing around the bolt, apply...
09-26-2018, 04:42 PM
Replies: 12
Views: 695
Posted By projectnitemare

I wish it would be that easy.

I wish it would be that easy.
09-24-2018, 08:03 PM
Replies: 12
Views: 695
Posted By projectnitemare

To make you feel better, mine started leaking...

To make you feel better, mine started leaking around 36k. Dealer had it for over 2 weeks and it started leaking again before the next oil change.
Replies: 11
Views: 593
Posted By projectnitemare

If you are moving all the parts from one housing...

If you are moving all the parts from one housing to another, it's practically a rebuild. Once I'm that deep I invest in new bearings and a master overhaul kit will come with all the shims and seals....
Showing results 1 to 15 of 499
 


 
Forum Jump

Contact Us About Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.