Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: four-sixty-power
Showing results 1 to 15 of 500
Search took 0.38 seconds.
12-03-2018, 04:28 AM
Replies: 16
Views: 484
Posted By four-sixty-power

Check if the fuse panel has corrosion on the...

Check if the fuse panel has corrosion on the backside of it, this means unscrewing it from the firewall under the dash.

Have you put the steering wheel back on after changing the turn signal...
12-03-2018, 04:22 AM
Replies: 10
Views: 385
Posted By four-sixty-power

On the dash there was a glue on placard that says...

On the dash there was a glue on placard that says HIGH OUTPUT between the radio and heater controls. It could have been pried off or fallen off over the years.

The heater boxes themselves were...
11-30-2018, 12:37 AM
Replies: 3
Views: 219
Posted By four-sixty-power

The hardest thing to source will be the latch...

The hardest thing to source will be the latch support that the latch bolts to, that holds the back of the benchseat up, as it is spot welded to the cab. I swapped a bench seat in and removed the...
11-27-2018, 02:56 PM
Replies: 7
Views: 372
Posted By four-sixty-power

Remove 3 screws holding visor to inside of cab. ...

Remove 3 screws holding visor to inside of cab.
Remove visor from metal rod.
Bend metal rod to create resistance against visor when positioned up or down, but still straight enough to not be...
11-27-2018, 06:47 AM
Replies: 5
Views: 431
Posted By four-sixty-power

You can either unbolt and remove the tailgate...

You can either unbolt and remove the tailgate handle latch(3 bolts on inside of cargo area of box on back of tailgate, or where you would sit on the tailgate when it is down), or just unclip the...
11-27-2018, 06:35 AM
Replies: 3
Views: 251
Posted By four-sixty-power

If springs are not holding up the hood when open,...

If springs are not holding up the hood when open, then you need new springs. IF you are wanting the hood to "pop" up when you use the hood latch, then you need a new popper spring that is mounted at...
11-27-2018, 06:20 AM
Replies: 4
Views: 299
Posted By four-sixty-power

In the diagram shown here (and out in the field)...

In the diagram shown here (and out in the field) the part identified as part number 431D76 does use 3 bolts to attach it to the tailgate. On the inside of the tailgate, for each of the bolts, there...
11-27-2018, 06:04 AM
Replies: 10
Views: 459
Posted By four-sixty-power

Just have to crouch down and lay on the floor and...

Just have to crouch down and lay on the floor and look up the length of the brake pedal arm and follow it up and you will find the brake light switch, they are usually all plastic(black and white)...
11-27-2018, 05:57 AM
Replies: 12
Views: 500
Posted By four-sixty-power

You can always cut the smaller radiator opening...

You can always cut the smaller radiator opening bigger, there are already 2 holes drilled on the driver side near where the new opening cut will be made, these 2 holes are the new mounting/bolting...
11-27-2018, 05:50 AM
Replies: 16
Views: 828
Posted By four-sixty-power

For the "factory A/C" that has the big box under...

For the "factory A/C" that has the big box under the hood (not the 2 different dealer installed options, of either mounted below the dash or where the glove box used to be) you will also need A/C...
11-27-2018, 05:39 AM
Replies: 3
Views: 340
Posted By four-sixty-power

Rag joint ground wire is ground for the horn and...

Rag joint ground wire is ground for the horn and for the PRND21 light, or the cruise control setup, if I recall correctly.
11-27-2018, 05:36 AM
Replies: 5
Views: 340
Posted By four-sixty-power

I seem to recall that if the resistor goes then...

I seem to recall that if the resistor goes then it defaults to only running at full speed. So in this case I would suspect your switch is faulty.
11-22-2018, 02:13 AM
Replies: 25
Views: 1,934
Posted By four-sixty-power

Checked that input rod length is correct?

Checked that input rod length is correct?
11-22-2018, 01:35 AM
Replies: 75
Views: 5,915
Posted By four-sixty-power

Liking the build, keep going :)

Liking the build, keep going :)
11-22-2018, 01:16 AM
Replies: 79
Views: 7,686
Posted By four-sixty-power

What is the front bumper off of, there was one...

What is the front bumper off of, there was one like it for sale on craigslist up here off of a mercury car but I thought it would be too narrow, now I'm thinking I should have bought it for my truck!...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.