Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: blueoval79
Showing results 1 to 15 of 154
Search took 0.43 seconds.
05-08-2007, 02:53 PM
Replies: 8
Views: 2,375
Posted By blueoval79

yes, you can use the same motor mounts and...

yes, you can use the same motor mounts and flywheel.
05-07-2007, 05:16 PM
Replies: 9
Views: 559
Posted By blueoval79

Yes, it is down by the starter. When I replaced...

Yes, it is down by the starter. When I replaced mine I bought the 36 inch length and it fit fine.
05-07-2007, 04:58 PM
Replies: 3
Views: 407
Posted By blueoval79

Do you know where I can get the crossover kit at?

Do you know where I can get the crossover kit at?
05-05-2007, 04:32 PM
Replies: 3
Views: 407
Posted By blueoval79

drop pitman arm

I have a 79 f250 3/4 ton 4 wd with a 6 inch susp. and 3 inch body lift. Does anybody know where I can find a drop pitman arm and a buddy of mine said I snapped a tie-rod, but i think it's the drag...
05-04-2007, 07:31 PM
Replies: 4
Views: 1,796
Posted By blueoval79

yes, cold level is for when your engine is still...

yes, cold level is for when your engine is still cold and hot level is when ur engine i running
05-04-2007, 07:21 PM
Replies: 11
Views: 570
Posted By blueoval79

Looks like stock to me. Your front leaf springs...

Looks like stock to me. Your front leaf springs basically have no curve to them @ all.
05-04-2007, 05:19 PM
Replies: 27
Views: 1,384
Posted By blueoval79

I ordered mine from JC Whitney about 4 years ago...

I ordered mine from JC Whitney about 4 years ago and they went for around $40.
05-04-2007, 05:15 PM
Replies: 2
Views: 296
Posted By blueoval79

Truck won't turn over

Hey guys, it's been about 2 years since i was on here last and about that long since i ran my truck. It's a 79 f250 custom 3/4 ton 4wd w/ a 6.6L. I changed my starter solenoid switch out and when i...
Replies: 8
Views: 562
Posted By blueoval79

U-joint replacement

I snapped both the front and rear u-joints on my rear driveshaft.
My question is how would i go about replacing them(i.e. tools needed)and if this is a tough and time consuming job.
10-03-2003, 09:53 PM
Replies: 1
Views: 401
Posted By blueoval79

One word. CENTERFORCE.

One word. CENTERFORCE.
10-03-2003, 09:49 PM
Replies: 5
Views: 594
Posted By blueoval79

dash swap?

Are there any dashes that will fit in a 79, like one perhaps from a 97 f250 w/ minor fab work?
09-18-2003, 06:25 PM
Replies: 3
Views: 462
Posted By blueoval79

Interchangeable front clips?

I'm thinking about purchasing a 89 Bronco with 87,000 miles on it for $2,000. The interior is in great shape and the exterior has minor rust just above the rear quarter panel, and some paint...
05-12-2003, 02:11 PM
Replies: 7
Views: 369
Posted By blueoval79

wrenches to remove tranny

I pulled my tranny(NP435) out and slid it on the cross member when i was replacing the clutch. Next time i'll just yank the motor, MUCH easier
05-12-2003, 02:05 PM
Replies: 5
Views: 421
Posted By blueoval79

Complete Ford Truck Wiring harness availability?

I heard Painless is just the opposite, PAINFUL! I went to the local junk yard and pulled one out of a donor truck. Alot CHEAPER, and EASIER.
05-02-2003, 07:07 PM
Replies: 1
Views: 300
Posted By blueoval79

79 cab size ?

Will a roll cage for a 79 F100 standard cab fit into a standard cab of a 79 F250?
Showing results 1 to 15 of 154
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.