Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: 3twinridges
Showing results 1 to 15 of 500
Search took 0.13 seconds.
Replies: 21
Views: 886
Posted By 3twinridges

I have had good luck with POR on stuff that would...

I have had good luck with POR on stuff that would be near impossible to get back to clean metal like the interior of doors and running it through tight spots like the bed pockets and cab frame...
Replies: 168
Views: 20,469
Posted By 3twinridges

Making progress still. Finishing up the final...

Making progress still. Finishing up the final sanding on the front clip and rough fitting it. Lots of high build and blocking to get to this point. Weather has turned colder and so our favorable days...
11-04-2018, 08:02 PM
Replies: 2
Views: 166
Posted By 3twinridges

Not that I could see, I assume when you say boss...

Not that I could see, I assume when you say boss you are referring to a threaded insert or a stud. On the 52 cab there is an unpunched cutout about three inches above the cab floor even with the...
11-04-2018, 06:07 PM
Replies: 2
Views: 166
Posted By 3twinridges

52 cab ground

parts book says the engine to cab ground strap attaches to the cab with a 5/16 bolt. I have the correct strap and mocking it up from the bellhousing I only see one cab cutout that will fit a 5/16...
11-03-2018, 10:00 PM
Replies: 5
Views: 296
Posted By 3twinridges

The quality and fit of some repop parts is...

The quality and fit of some repop parts is frustrating to say the least. I had two situations today, a repop pitman arm and 52 front hood emblem, where I elected to use a good reconditioned...
11-01-2018, 06:04 PM
Replies: 6
Views: 432
Posted By 3twinridges

The shrinker and stretcher set from eastwood...

The shrinker and stretcher set from eastwood works for patch panels pretty well. I was able to shrink some 16 gauge for the doublers also.

JB
11-01-2018, 02:26 PM
Replies: 24
Views: 772
Posted By 3twinridges

Is the carb body newly plated in Chromate? JB

Is the carb body newly plated in Chromate?

JB
10-31-2018, 01:17 PM
Replies: 5
Views: 270
Posted By 3twinridges

That 3 spd will bolt up to both the 226 and 239...

That 3 spd will bolt up to both the 226 and 239 original bellhousing.

JB
10-27-2018, 11:37 PM
Replies: 12
Views: 467
Posted By 3twinridges

Cup is held in by the nut. I just rebuilt a...

Cup is held in by the nut.

I just rebuilt a box tonight, the clear coat is drying now. I sealed the threads on all the bolts and used “the right stuff” under the star washer. I am going to gamble...
10-25-2018, 10:10 PM
Replies: 12
Views: 467
Posted By 3twinridges

I am guessing to keep debri from entering the box...

I am guessing to keep debri from entering the box from the steering tube and to keep any sloshing gear oil from coming out. I saturated mine with some oil.

JB
10-25-2018, 09:50 PM
Replies: 12
Views: 467
Posted By 3twinridges

The felt donut slides down the steering shaft to...

The felt donut slides down the steering shaft to seal the top of the box. It just sits on top. Not sure about the circle, maybe it’s just the cutout of the donut?

JB
10-12-2018, 05:25 PM
Replies: 1
Views: 229
Posted By 3twinridges

EAB v8 heads

Not sure which is cooler, NOS EAB flathead V8 heads or the wood crates they are in. I probably will never be able to bring myself to open them!

JB
...
10-12-2018, 05:20 PM
Replies: 11
Views: 590
Posted By 3twinridges

I am no expert but I think the vent window...

I am no expert but I think the vent window assembly came as one piece, frame parts and all. The 51-52 has the push button lock and 48-50 doesn’t. The 51-52 also came with a chrome option. I think...
10-10-2018, 09:02 PM
Replies: 11
Views: 590
Posted By 3twinridges

The division bar has room for adjustment. Based...

The division bar has room for adjustment. Based on what I see the bottom of the division bar needs to shift forward a little to close the gap at the bottom.

JB
10-07-2018, 11:01 AM
Replies: 2
Views: 250
Posted By 3twinridges

Thanks Ross, will give the RTV a go on that star...

Thanks Ross, will give the RTV a go on that star washer area.

JB
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.