Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: EL_JEFE32
Showing results 1 to 15 of 95
Search took 0.23 seconds.
Replies: 2
Views: 555
Posted By EL_JEFE32

Dana 7U hub

Just wondering if any other Dana 70 hubs were interchangeable with a 70U. I have spun a race, destroyed a bearing and almost a spindle. I went to the lovely El Paso yards today to find some Dana 70s...
Replies: 27
Views: 934
Posted By EL_JEFE32

I'll probably run off the front tank until I can...

I'll probably run off the front tank until I can get something made or find some heat shield to stick to the tank and under the straps. Now I just need to figure out the best place to put my painless...
Replies: 27
Views: 934
Posted By EL_JEFE32

I have one spot that is 2 inches away from the...

I have one spot that is 2 inches away from the pipe and it tapers away to about 3 inches but the rough average is about 2 1/2 inches. Looking at it I believe it should be fine. Any thoughts?
Replies: 11
Views: 520
Posted By EL_JEFE32

I second not needing the stabilizer but if its...

I second not needing the stabilizer but if its free well go for it. I have always used superlift myself but know others that have used your type system and they say that it rides smoother with the...
Replies: 27
Views: 934
Posted By EL_JEFE32

Well went out this morning and it worked fine...

Well went out this morning and it worked fine Twice. Maybe both were sticking so I'm going to put the original back on since it had a boot over the power and the new one doesn't. I don't want a open...
Replies: 14
Views: 1,001
Posted By EL_JEFE32

Yeah I see how it would prevent vapor lock and...

Yeah I see how it would prevent vapor lock and with safety systems in place they remedied the problems. I was just trying to make a comparison between the two with some pros and cons. I on a personal...
Replies: 14
Views: 1,001
Posted By EL_JEFE32

I would have to disagree with this. There is a...

I would have to disagree with this. There is a reason that our helicopters have engine driven fuel pumps as a primary. Yes they have in tanks at low psi to get it to the lines but the engine is based...
Replies: 27
Views: 934
Posted By EL_JEFE32

I agree it shouldn't be this complicated with a...

I agree it shouldn't be this complicated with a simple solenoid selector. I didn't think of putting two clear lines on to see what was happening but that is actually real smart thinking. If I don't...
Replies: 27
Views: 934
Posted By EL_JEFE32

That's what I figured as well especially with a...

That's what I figured as well especially with a 750 carb and at high idle due to the cold.
Replies: 27
Views: 934
Posted By EL_JEFE32

I just tried and looks fine. Maybe i am just...

I just tried and looks fine. Maybe i am just being an idiot but how many minutes would it run on fuel in the line. I am just going to put in on rear tank tomorrow and see if it chokes out and hook...
Replies: 27
Views: 934
Posted By EL_JEFE32

Well that was not it. I even rechecked the old...

Well that was not it. I even rechecked the old one off the battery and it works just fine. It has to be something external from the selector valve keeping it from coming off of the aux port since its...
Replies: 27
Views: 934
Posted By EL_JEFE32

But would it go from working to not working? And...

But would it go from working to not working? And I'm wondering if its something else since the last one was doing the same thing which led me to get this one. I just don't know what else would do it...
Replies: 27
Views: 934
Posted By EL_JEFE32

Checked power again just to be sure and no power...

Checked power again just to be sure and no power with switch on main tank and 12 v or so in the aux setting as it suppossed to be. There is noway for it to be electrical as its direct to switch to...
Replies: 27
Views: 934
Posted By EL_JEFE32

Ok so here's the update... I wired everything...

Ok so here's the update... I wired everything from scratch for the dual tanks by taking a schematic and wiring off that using my own homemade wiring harnesses since my origional cab didn't come with...
Replies: 8
Views: 454
Posted By EL_JEFE32

Look at the merry Christmas post it has an ad...

Look at the merry Christmas post it has an ad that says 80-81 now with optional auto hubs. So that means there somewhere!
Showing results 1 to 15 of 95
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.