Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Mistro
Showing results 1 to 15 of 114
Search took 0.46 seconds.
Replies: 8
Views: 297
Posted By Mistro

oil plugs for solid lifters -- tap sizes?

Tap the small hole to 1/8NPT and the outer hole to 1/4 NPT but I dont know if this is rare or whatnot m but my larger holes were drilled to 17/32 from FORD so the tap woulnt work. I am now going to...
12-28-2002, 03:08 AM
Replies: 3
Views: 231
Posted By Mistro

I want to get a PowerStroke but have a few Questions.

I would like to buy a early Powerstroke but was wondering if thre is anything wrong with the early powerstrokes. Is there just some basic info that you could share with me. What should I watch out...
Replies: 5
Views: 277
Posted By Mistro

Just how is a thermostat SUPPOSED to stay in?

[updated:LAST EDITED ON 24-Dec-02 AT 03:40 AM (EST)]To keep my thermostat in place in the housing I have to use the smaller diameter gasket that comes with my fel-pro gasket kit. The smaller...
Replies: 8
Views: 369
Posted By Mistro

FE 428 Cobra Jet in International W6

I woulnt be worried about the tires coming apart if they are in decent condition. If they still have fluid in them that might make them a little bit more prone to coming apart. The guys at the NTPA...
12-23-2002, 10:13 PM
Replies: 1
Views: 723
Posted By Mistro

I Need A Pair Of Front Disk Brake Dust Shields

I have heard that you dont need them but I feel that with winter here it is neccesary to have them to keep salt out of my brakes and am wondering if anybody Repro's them. If you guys could take a...
12-10-2002, 06:36 PM
Replies: 10
Views: 532
Posted By Mistro

Need Stiffer Springs or Should I Cut coil springs ?

I have a 4X4 so I dont plan on putting on a sway bar. I need the stiffest springs for what I want to do with the truck.
Replies: 3
Views: 459
Posted By Mistro

How To Setup Pinion Bearing Pre-Load On A Dana 44

Just like the Dumb-ass that I am I messed up the shimms when I took my front end apart and now have to get it back togather. I know that there were shims in front and behind the rear pinion...
12-06-2002, 08:25 PM
Replies: 3
Views: 404
Posted By Mistro

How To Setup Pinion Bearing Pre-Load On A Dana 44

Just like the Dumb-ass that I am I messed up the shimms when I took my front end apart and now have to get it back togather. I know that there were shims in front and behind the rear pinion...
12-05-2002, 05:01 PM
Replies: 10
Views: 532
Posted By Mistro

Need Stiffer Springs or Should I Cut coil springs ?

I need some new coil springs but I would like some stiffer ones and retain the stock ride height and the only stiffer springs I can get are of the lifted variety so I was wondering if I could cut...
12-02-2002, 11:33 PM
Replies: 3
Views: 419
Posted By Mistro

Ball Joints.

What is the name of the tool? Thanx
12-01-2002, 10:44 PM
Replies: 3
Views: 419
Posted By Mistro

Ball Joints.

I am repalcing my worn ball joints and when I got my new ones ther is a replacement threaded top angled spacer. The part that screws into the top spindle arm on the dana 44 axle tube for the taper of...
11-29-2002, 01:20 AM
Replies: 2
Views: 236
Posted By Mistro

Putting in a Pertronix Igniter II, Now where is this resistance wire?!?!

Or whatever. Is it the Red wire that goes from the coil to the ignition? Where do I splice in a new line at or what would be the bast way to bypass it or whatever. Thanx guys
Replies: 6
Views: 933
Posted By Mistro

Torque for ARP Head Bolts?

I Use the ARP moly lube, it is good stuff and use the trread sealer anywhere the threads go through into the coolant system. You can use moly lube on all the bolts too, it will give you more...
Showing results 1 to 15 of 114
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.