Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Project-55
Showing results 1 to 15 of 499
Search took 0.18 seconds.
03-25-2017, 12:15 AM
Replies: 1,401
Views: 253,206
Posted By Project-55

That is so cool, I want one. look at the size of...

That is so cool, I want one. look at the size of that beast,,,,wow
10-20-2016, 12:04 PM
Replies: 28
Views: 3,365
Posted By Project-55

I have a 4 post lift with a slide jack and love...

I have a 4 post lift with a slide jack and love it for 95% of everything I do. The only drawback is when you want to work close to the rocker panels is that you have to work over the side ramps.
12-12-2015, 08:14 PM
Replies: 639
Views: 174,908
Posted By Project-55

lol, I would have to refer back to that area of...

lol, I would have to refer back to that area of the build but if memory serves me, the spacers were 13 inches long, 1 1/2 thick, and 2 inches wide. I cut the basic taper to match the frame with a...
07-13-2015, 08:09 PM
Replies: 4
Views: 1,742
Posted By Project-55

Crown Vic IFS Steering question

Ok, so I pugged in a CV IFS into my truck and am finally getting around to pluming the power rack, except for the small problem of not being able to figure out which port is input pressure and which...
07-13-2015, 07:50 PM
Replies: 10
Views: 665
Posted By Project-55

The crown vic cop car that I acquired my 4.6 from...

The crown vic cop car that I acquired my 4.6 from was running waterless coolant and I must say that the interior surfaces of the block and radiator looked brand new. But that stuff is slimy as all...
07-04-2015, 01:11 PM
Replies: 639
Views: 174,908
Posted By Project-55

I originally intended to keep the factory heater,...

I originally intended to keep the factory heater, took it all apart put new brushes in the fan motor, boiled out the heater core, bead blasted the entire unit and repainted it.
But my lovely wife...
07-02-2015, 08:58 PM
Replies: 639
Views: 174,908
Posted By Project-55

Vintage air mis-sent me the 56 install kit which...

Vintage air mis-sent me the 56 install kit which I tossed onto the shelf,,,, if you want it just say so because I will not use it,
There is the ABS panel which fits under the dash for the vents, the...
07-02-2015, 08:47 PM
Replies: 639
Views: 174,908
Posted By Project-55

I kill a LOT of card board boxes, it allows you...

I kill a LOT of card board boxes, it allows you to try multiple styles without putting in hours of cutting and bending only to FAIL...}>
07-02-2015, 08:44 PM
Replies: 639
Views: 174,908
Posted By Project-55

I sure wish I could run that AC unit now it was...

I sure wish I could run that AC unit now it was almost 90 inside the hangar today as I installed the condenser and dryer, thought I was going to melt.
07-02-2015, 08:02 PM
Replies: 639
Views: 174,908
Posted By Project-55

I am jumping between several things right now...

I am jumping between several things right now depending on my ambition because it is so flippin hot right now.


I am working on the vintage air kit that my wife not only insisted on but bought...
06-29-2015, 01:12 PM
Replies: 74
Views: 29,969
Posted By Project-55

It's nice to hear that you are still standing, I...

It's nice to hear that you are still standing, I kinda figured that you were secretly slaving away on the truck and were going to be posting photo's of your finished beast.


You gotta start...
06-24-2015, 01:47 PM
Replies: 639
Views: 174,908
Posted By Project-55

Its kind of a Fred Flintstone way of rolling the...

Its kind of a Fred Flintstone way of rolling the tailgate skins. what I do is tack weld the edge of my sheet metal blank to a section of 3/4 inch water pipe (alignment is critical to get a perfect...
06-24-2015, 01:03 PM
Replies: 33
Views: 6,599
Posted By Project-55

That is a great looking truck, overall it looks...

That is a great looking truck, overall it looks like it was well maintained.


What are your plans for the truck BTW?
06-24-2015, 10:27 AM
Replies: 639
Views: 174,908
Posted By Project-55

full height tailgate

197745 (http://s1249.photobucket.com/user/project-55/media/LAPTOP/tailgate/20150517_154607_resized_zps6yae4sag.jpg.html)
I rolled the skin to match the roll of the bed sides.


197746...
06-23-2015, 09:03 PM
Replies: 639
Views: 174,908
Posted By Project-55

I have thought about putting a cap panel between...

I have thought about putting a cap panel between the 2 headers to hide the tank but the tank actually looks pretty dam good so I think I will leave it as is for now. I can always add a cap later.

...
Showing results 1 to 15 of 499
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.