Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Greyf100
Showing results 1 to 15 of 499
Search took 1.16 seconds.
Replies: 63
Views: 3,261
Posted By Greyf100

My 81 F100, 4700 GVWR, 10" brakes bumper pulls a...

My 81 F100, 4700 GVWR, 10" brakes bumper pulls a 2200lbs camper fine. It does have a 1990 roller 302 in it though with c6 and 3.25 gears. Tows / stops just fine, even without trailer brakes on the...
Replies: 5
Views: 1,097
Posted By Greyf100

I don't really know what initial timing was set...

I don't really know what initial timing was set at, but it ran fine with the other carb. I changed the carb and it wouldn't run so i adjusted so it would run.
Replies: 5
Views: 1,097
Posted By Greyf100

what i dont understand is that it didnt start...

what i dont understand is that it didnt start dieseling until i changed the carb......
Replies: 5
Views: 1,097
Posted By Greyf100

Carb TUning Help

Truck ran great with the old used Eddy 600cfm, i switched to a holley Street avenger 570cfm to try and gain some MPG's. Every since the change I can either get the truck to run & idle great with...
Replies: 10
Views: 871
Posted By Greyf100

Hooker has a "bolt on" true dual setup, i'm using...

Hooker has a "bolt on" true dual setup, i'm using it but not real happy with the cross over. It hangs too far below the trans cross member, and I cant get the passenger side collector up high enough...
Replies: 45
Views: 1,573
Posted By Greyf100

Edelbrock? 1403 = 500cfm, 1406 = 600cfm...both...

Edelbrock? 1403 = 500cfm, 1406 = 600cfm...both with elec choke
Replies: 7
Views: 1,685
Posted By Greyf100

carb selection opinions

Specs:
'81 F100
'89 Roller, NON-HO 302
Performer 289 intake
stock cam
stock heads
stock truck manifolds with 2.25" true duals and thrush welded mufflers, no cats
3.25 gears
30x9.50 tires
c6...
Replies: 2
Views: 921
Posted By Greyf100

I ran both out in the stock location, behind the...

I ran both out in the stock location, behind the passenger side rear wheel. Personally I dont like running them straight out the back, if you should get hit in the rear bumper it could do alot of...
Replies: 17
Views: 842
Posted By Greyf100

Love my Thrush's!! Nice rumble, good tone,...

Love my Thrush's!!

Nice rumble, good tone, not too loud.

Thrush 17655 - Thrush Welded Mufflers - Overview - SummitRacing.com (http://www.summitracing.com/parts/WLK-17655/)
Replies: 5
Views: 1,277
Posted By Greyf100

or just post up a pic, most that have dealt with...

or just post up a pic, most that have dealt with the trucks long enough can tell you by intake design / dimensions and / or valve cover bolt pattern.
Replies: 11
Views: 2,801
Posted By Greyf100

If you have some machined they need to be to...

If you have some machined they need to be to exact powertrax specs, if you can find them. I'm sure its proprietary design info and Eaton wont give that info out. I would personally just buy a new...
Replies: 19
Views: 10,633
Posted By Greyf100

I put a set of buckets from a '95 Explorer,...

I put a set of buckets from a '95 Explorer, drilled 2 holes and used 1x1" square tubing for a spacer on the inside rear mount.
Replies: 11
Views: 2,801
Posted By Greyf100

I hope you setup the backlash and carrier preload...

I hope you setup the backlash and carrier preload on the "new" carrier or else the clips will be the last of the things you need to worry about.

There should be a large rod that goes down through...
Replies: 45
Views: 3,348
Posted By Greyf100

what about adding a weight distro hitch in...

what about adding a weight distro hitch in addition to the elec trailer brakes?
Replies: 11
Views: 1,728
Posted By Greyf100

sure you have kingpins? My '81 F100 with...

sure you have kingpins?

My '81 F100 with power brakes and 5 on 4.5" Bp has ball joints.
Showing results 1 to 15 of 499
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.