Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: jk080
Showing results 1 to 15 of 500
Search took 0.33 seconds.
Replies: 2
Views: 125
Posted By jk080

Googling to first number you listed...

Googling to first number you listed "6C3P-7000-DB" comes back as a 5R110W transmission, and it most likely is the transmission in the vehicle. Don't know if it has PTO capabilities but you should be...
Replies: 1
Views: 172
Posted By jk080

If the lugs look good I would just run it, weak...

If the lugs look good I would just run it, weak spots are all over this transmission you would have to replace just about everything inside to a custom built part that addresses a particular weak...
Replies: 5
Views: 421
Posted By jk080

Low fluid or a missing or loose filter is usually...

Low fluid or a missing or loose filter is usually the cause for this, maybe overfill it to see if the condition goes away or just pull the pan and check the filter.
Replies: 3
Views: 288
Posted By jk080

My guess would be that the joint on the front...

My guess would be that the joint on the front shaft failed and the shock of that coming apart broke the transfer case housing, at that point the transfer case could fall out. I have seen this a few...
Replies: 7
Views: 326
Posted By jk080

If the fluid change dont fix it then the...

If the fluid change dont fix it then the converter may be the problem.
Replies: 10
Views: 385
Posted By jk080

I just bought a new set of Bench Buddy brushes,...

I just bought a new set of Bench Buddy brushes, use them so much I wear them out. Just use a fine emery cloth on the valve to clean it up, try not to round the edges of the valve lands
Replies: 10
Views: 385
Posted By jk080

If that valve is stuck it very well may be your...

If that valve is stuck it very well may be your problem, clean it and make sure it moves freely in the bore and put it all back together and see if you have lockup, if not I would suspect the...
Replies: 10
Views: 385
Posted By jk080

The TC Pressure Limit control valve is the only...

The TC Pressure Limit control valve is the only valve that has to do with the converter with this transmission, it rarely sticks or has issues, maybe its assembled incorrectly. If this valve looks...
Replies: 3
Views: 301
Posted By jk080

Ring and pinion look good and the spider gears...

Ring and pinion look good and the spider gears look typical, most of the time the pinion bearings are the culprit for noises. The only way to know for sure is to take it completely apart and look, at...
Replies: 2
Views: 185
Posted By jk080

It should work as long as it fits the ring gear...

It should work as long as it fits the ring gear and sun gear, count the teeth.

If the planet had chipped teeth make sure the ring gear and sun gear are not damaged as well.
Replies: 61
Views: 81,266
Posted By jk080

The overdrive band has to apply during the 3-4...

The overdrive band has to apply during the 3-4 shift, if it doesn't apply it will feel like a neutral because the forward drum is released during that shift, so yes your description of your problem...
Replies: 4
Views: 260
Posted By jk080

I had a 7.3 diesel that I chased this code after...

I had a 7.3 diesel that I chased this code after a rebuild, turned out to be the cam sensor. Just something to keep in mind if it keeps returning.
Replies: 7
Views: 326
Posted By jk080

I have noticed that the converter clutch can make...

I have noticed that the converter clutch can make a knock or a shock when it releases with this transmission sometimes, changing the fluid should help with this. I wouldn't use that additive after...
Replies: 2
Views: 149
Posted By jk080

Try disconnecting the electric fan clutch. ...

Try disconnecting the electric fan clutch.

The 12 V feed for the TR sensor is shared with the 12 V feed for the fan speed sensor within the PCM and a short in the fan clutch circuit can pull the...
04-15-2018, 09:07 PM
Replies: 9
Views: 313
Posted By jk080

Definitely replace that valve, it can stick and...

Definitely replace that valve, it can stick and dump the pressure for sure, you will need a pump alignment tool to get the pump back together correctly.

I use the Superior valve in these, I like...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.