Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: ranger pat
Showing results 1 to 15 of 500
Search took 0.45 seconds.
06-19-2018, 08:21 PM
Replies: 3
Views: 138
Posted By ranger pat

I see you live in AZ and drive a 1983 Ranger. ...

I see you live in AZ and drive a 1983 Ranger. Lots of auto supply stores sell premade straight fuel and brake lines in different lengths, diameters etc. Autozone type stores, NAPA, etc. You will...
06-18-2018, 09:31 PM
Replies: 5
Views: 194
Posted By ranger pat

I seem to remember they are different diameters. ...

I seem to remember they are different diameters. The large one is supply and the smaller one is the return.
06-18-2018, 08:05 AM
Replies: 2
Views: 153
Posted By ranger pat

Take your Ranger to an automatic transmission...

Take your Ranger to an automatic transmission shop and have them evaluate it.
06-15-2018, 10:07 PM
Replies: 2
Views: 153
Posted By ranger pat

l will start the list. Flywheel has to replace...

l will start the list. Flywheel has to replace the flex plate used on an auto. Through out bearing in the flywheel, new starter for the different number of teeth in the flywheel. Brake and clutch...
06-13-2018, 07:38 PM
Replies: 5
Views: 220
Posted By ranger pat

https://www.carid.com/1992-ford-ranger-floor-pans/...

https://www.carid.com/1992-ford-ranger-floor-pans/

These guy show replacement panels for the entire floor.
06-12-2018, 12:58 PM
Replies: 2
Views: 335
Posted By ranger pat

I got a set of tubular stainless steel headers...

I got a set of tubular stainless steel headers off a 92 T-Bird 302 and had them "ceramic" powder coated in silver. They are a lot like block huggers, except they exit near the rear of the engine and...
06-04-2018, 03:22 PM
Replies: 26
Views: 692
Posted By ranger pat

How about using a spring loaded toggle switch...

How about using a spring loaded toggle switch remotely mounted anywhere that you toggle for engine start. That would not keep you from starting the engine in gear, but you could always
ensure the...
06-04-2018, 09:03 AM
Replies: 3
Views: 309
Posted By ranger pat

The oil pan will be a steel stamped metal...

The oil pan will be a steel stamped metal construction and the transmission will be an aluminum casting.
06-04-2018, 08:57 AM
Replies: 28
Views: 687
Posted By ranger pat

Sounds nice, but I would not purchase any vehicle...

Sounds nice, but I would not purchase any vehicle without a clear title. You could research how to obtain a new title in your state, but make are you can legally register and license the vehicle...
05-26-2018, 01:06 PM
Replies: 7
Views: 323
Posted By ranger pat

Make sure there is spark at one of the spark plug...

Make sure there is spark at one of the spark plug and then all you will need is fuel. Listen for the electric fuel pump when you turn on the key. If you hear that, check fuel pressure at the fuel...
05-24-2018, 07:49 AM
Replies: 6
Views: 361
Posted By ranger pat

Does the engine turn over, but not start? Then...

Does the engine turn over, but not start? Then you probably have a fuel delivery problem. If the engine does not turn over, you have an electrical problem.
Turn off the a/c fan and listen for...
05-20-2018, 06:07 PM
Replies: 4
Views: 199
Posted By ranger pat

There is another fuse under the hood that powers...

There is another fuse under the hood that powers fuse 12 in the drivers side dash panel. Underhood fuse 3 protects fuses in the dash panel.
Those dash panel fuses are #4 Hazard flashers, fuse #8...
05-20-2018, 07:07 AM
Replies: 1
Views: 106
Posted By ranger pat

Close out this thread, I figured how to break...

Close out this thread, I figured how to break loose the choke cap so it would rotate and I finished adjusting the choke. The trick was to grab the top and bottom of the cap and not rotate it but...
05-19-2018, 09:03 PM
Replies: 1
Views: 106
Posted By ranger pat

Adjusting the choke

I installed a new Holley 600 and need to adjust the choke setting. I loosened up the three screws holding the plastic choke cap, but am unable to turn the cap. My directions say to hold the...
05-18-2018, 11:09 AM
Replies: 2
Views: 298
Posted By ranger pat

1. Stainless fender inners go under the firewall...

1. Stainless fender inners go under the firewall support brackets as they are painted parts and have a small upturn that would not allow the ss inners to fit above them.
2. The front fender braces...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.