Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: shorod
Showing results 1 to 15 of 500
Search took 0.28 seconds.
06-16-2018, 08:21 AM
Replies: 5
Views: 140
Posted By shorod

You can check for a round connector under the...

You can check for a round connector under the rear taillights (I don't recall which one they are typically under). If the plug is there and has never been used before, there will be a rubber cap in...
06-15-2018, 05:40 PM
Replies: 5
Views: 140
Posted By shorod

You need a trailer brake controller and, if your...

You need a trailer brake controller and, if your Explorer has a pre-wired plug for the trailer brake controller, you will also need the harness to take advantage of the pre-wired connector. Then you...
06-14-2018, 06:46 AM
Replies: 5
Views: 222
Posted By shorod

There might be a secondary air pump or something...

There might be a secondary air pump or something down in that area, but I'll caution again that sounds in spaces like an engine compartment can easily trick a person in to thinking they are coming...
06-13-2018, 06:46 AM
Replies: 5
Views: 222
Posted By shorod

Was the humming sound constant or did it change...

Was the humming sound constant or did it change with engine speed? If it changed with engine speed it could have been one of the pulleys or it could also have been the fan clutch having actually...
06-11-2018, 07:07 AM
Replies: 1
Views: 137
Posted By shorod

You might try shifting the transmission to...

You might try shifting the transmission to neutral and trying with the key again. Maybe somehow you jostled the park/neutral safety switch during the starter install (even though they are not very...
06-10-2018, 08:57 AM
Replies: 2
Views: 146
Posted By shorod

Assuming you didn't have a front seat passenger...

Assuming you didn't have a front seat passenger at the time who wasn't wearing their seat belt, I'd suspect you want to check the driver's seat belt latch along with the wiring under the seat. Since...
06-09-2018, 03:25 PM
Replies: 2
Views: 166
Posted By shorod

You'd most likely be better off to just replace...

You'd most likely be better off to just replace the 2005 Explorer with one that has the rear A/C already. You'd need to plumb the rear heater core and rear A/C evaporator core, change out the A/C...
06-06-2018, 08:52 PM
Replies: 2
Views: 151
Posted By shorod

Per the factory service manual, the resistance of...

Per the factory service manual, the resistance of the HO2S heater + and heater - should be 5 ohms. The resistance from heater + and VPWR should be 3 - 30 ohms. The isolation to the other wires...
06-01-2018, 05:41 PM
Replies: 3
Views: 205
Posted By shorod

Have you monitored the fuel pressure when it is...

Have you monitored the fuel pressure when it is idling as well as when it is running poorly? You mentioned the truck will run good for a minute or a few but then will settle down to below 2000. Are...
05-24-2018, 06:59 AM
Replies: 2
Views: 169
Posted By shorod

If your 1995 uses an ignition control module,...

If your 1995 uses an ignition control module, that would be my first suspect. The ICM in earlier Fords were pretty well-known for causing tachometer issues during early stages of failure.

-Rod
05-17-2018, 07:07 AM
Replies: 1
Views: 161
Posted By shorod

It's likely that the issue is due to a failed...

It's likely that the issue is due to a failed blower motor speed control. It's either an issue with the blower motor speed control or you have something grounding the blower motor ground. Power is...
05-11-2018, 06:49 AM
Replies: 5
Views: 327
Posted By shorod

Looks a bit like part of the caliper threads are...

Looks a bit like part of the caliper threads are still in the bleeder screw threads. If not, then pieces of the bleeder screw threads are still in the old caliper. Good call to replace the caliper....
05-10-2018, 06:56 AM
Replies: 1
Views: 152
Posted By shorod

It sounds like your Explorer either has a vacuum...

It sounds like your Explorer either has a vacuum leak or an ignition misfire that is happening when things get warmed up. It could be due to an ignition module with a bad solder joint (although I'm...
05-09-2018, 06:49 AM
Replies: 5
Views: 327
Posted By shorod

Wow, interesting. Hopefully the bleed screw is...

Wow, interesting. Hopefully the bleed screw is just loose. If it's not loose and not just rusted in place, carefully inspect the bore of the hole for cracks before just replacing the bleeder screw....
05-08-2018, 06:59 AM
Replies: 5
Views: 327
Posted By shorod

So did you do a two-person bleed or just a...

So did you do a two-person bleed or just a gravity feed? There are multiple ways it could be done and considered a "tube in glass" method.

Since it's a 2003, I'd recommend you either do a...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.