Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 15 of 500
Search took 0.35 seconds.
Search: Posts Made By: cadunkle
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks Yesterday, 03:52 PM
Replies: 22
Views: 668
Posted By cadunkle
Well done, nicely made and clean install.

Well done, nicely made and clean install.
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks Yesterday, 03:47 PM
Replies: 4
Views: 128
Posted By cadunkle
Just run a new 4ga charge cable to the battery....

Just run a new 4ga charge cable to the battery. You can tie the sense wire into that on the alternator if you're lazy but really you should run that back to the battery as well. Then tie in your key...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-20-2018, 08:58 PM
Replies: 20
Views: 730
Posted By cadunkle
I don't have a neutral in the wiring to my...

I don't have a neutral in the wiring to my compressor. I could use a relay and pull 110v from a nearby outlet, but at that point I'd rather spend the money for a 220v motor. I do have a cquirrel cage...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-20-2018, 08:53 PM
Replies: 12
Views: 410
Posted By cadunkle
Could teh rotor have not been fully seated,...

Could teh rotor have not been fully seated, striking the cap posts?
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-20-2018, 09:45 AM
Replies: 8
Views: 366
Posted By cadunkle
Westach makes some nice 2" gauges in both single...

Westach makes some nice 2" gauges in both single and dual. I have some of their dual guages.
http://www.westach.com/
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-19-2018, 10:43 PM
Replies: 20
Views: 730
Posted By cadunkle
Yes, it's an intercooler, out of pump through the...

Yes, it's an intercooler, out of pump through the cooler then into a Norgren water separator and into the tank after that. It keeps nearly all moisture out of the tank. It'll drop temps from 300*+...
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-18-2018, 04:09 PM
Replies: 8
Views: 306
Posted By cadunkle
I believe you can use a governor spring from a GM...

I believe you can use a governor spring from a GM 6.2 pump to raise it to around 4000-4200. You better build a very stout bottom end if you go that route though.
Forum: Pre-Power Stroke Diesel (7.3L IDI & 6.9L) 02-16-2018, 10:16 PM
Replies: 13
Views: 520
Posted By cadunkle
What is the taper on the worst bore?

What is the taper on the worst bore?
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-16-2018, 10:11 PM
Replies: 6
Views: 433
Posted By cadunkle
You have eitehr D3VE or E6TE heads, effectively...

You have eitehr D3VE or E6TE heads, effectively identical. These heads can make around 700 HP when ported. Porting just takes time, even your first go around you'll be good for 500+ HP. Ford exhaust...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-16-2018, 10:04 PM
Replies: 7
Views: 401
Posted By cadunkle
Well damn that's a steal if it includes the...

Well damn that's a steal if it includes the tailgate. Wish it wasn't so far, wouldn't be bad even having to weld in the second fuel filler. If it was within an hour or two drive I'd be all over it.
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-16-2018, 09:44 PM
Replies: 20
Views: 730
Posted By cadunkle
Dry air as fast as it'll put it out...

Dry air as fast as it'll put it out...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-15-2018, 11:30 PM
Replies: 20
Views: 730
Posted By cadunkle
For blasting be sure you have the compressor to...

For blasting be sure you have the compressor to handle it. I have a HF blast cabinet with TP Tools gun. Compressor is a $400 HD special, older model 12.x CFM 3.x HP 60 gal single stage. I had to add...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-15-2018, 09:58 PM
Replies: 22
Views: 668
Posted By cadunkle
It must be the smog carbs that are problematic....

It must be the smog carbs that are problematic. NJ weather is more or less the same. 60s and sunny today now warm and raining. Was damn cold a week or two ago, gonna be below freezing this weekend...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-15-2018, 12:49 PM
Replies: 6
Views: 397
Posted By cadunkle
I've never heard of anyone swapping an FE into an...

I've never heard of anyone swapping an FE into an 80-97 truck. it's a silly swap to do since a 460 was a factory options and is a bolt in deal, especially if you're coming from a 351m/400. Not worth...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 02-15-2018, 12:42 PM
Replies: 10
Views: 440
Posted By cadunkle
I don't understand the point of going through a...

I don't understand the point of going through a nearly brand new engine if there is no problem and you don't want more power. What do you hope to gain?

personally I wouldn't waste a penny on a...
Showing results 1 to 15 of 500

 
Forum Jump

All times are GMT -5. The time now is 08:28 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.