Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 15 of 500
Search took 0.42 seconds.
Search: Posts Made By: Briansshop
Forum: 1987 - 1996 F150 & Larger F-Series Trucks Today, 09:25 AM
Replies: 2
Views: 147
Posted By Briansshop
As in crank case ventilation? Have mine...

As in crank case ventilation?

Have mine vented to atmosphere ATM. Push in breathers on the VCs and a vented can connected to the oil pan. Can is in front pass side of engine compartment.
...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks Yesterday, 09:17 AM
Replies: 34
Views: 663
Posted By Briansshop
^ Nice work ^

^ Nice work ^
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-20-2018, 09:22 PM
Replies: 25
Views: 716
Posted By Briansshop
Injector pump? Do you mean a HPOP? You can can...

Injector pump? Do you mean a HPOP? You can can buy a new one for less than $600 and swap it out in a day.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-20-2018, 09:21 AM
Replies: 25
Views: 716
Posted By Briansshop
I prefer the 7.3, but also like the 460. I'd go...

I prefer the 7.3, but also like the 460. I'd go with either motor if I found a clean low mileage one for a REASONABLE PRICE, since that might prove to be hard enough to do. Low mileage to me is less...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-18-2018, 10:08 AM
Replies: 42
Views: 1,199
Posted By Briansshop
I see. I've only tuned aftermarket EFI systems,so...

I see. I've only tuned aftermarket EFI systems,so I don't know much about factory PCM tuning. Just wondered if those comments were guesses or if someone actually knew the conditions for open loop.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-18-2018, 09:15 AM
Replies: 42
Views: 1,199
Posted By Briansshop
Then what is the case? Lets hear the conditions...

Then what is the case? Lets hear the conditions needed to open the loop.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-18-2018, 08:33 AM
Replies: 42
Views: 1,199
Posted By Briansshop
Not so sure about this. I've had the...

Not so sure about this. I've had the understanding that the only time, for emissions reasons, that a factory ecm allowed open loop was either above 4000 RPMs or WOT.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-17-2018, 06:02 PM
Replies: 19,450
Views: 1,946,750
Posted By Briansshop
Replaced the JUNK Optima Yellow Tops in my F350...

Replaced the JUNK Optima Yellow Tops in my F350 with XS Power D3400s

https://s26.postimg.org/h9htwaagp/20180216_155624.jpg (https://postimg.org/image/7c6t382ut/)
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-15-2018, 11:36 AM
Replies: 42
Views: 1,199
Posted By Briansshop
Yes, if the op can't install gears, complete axle...

Yes, if the op can't install gears, complete axle swap would be cheaper.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-15-2018, 07:06 AM
Replies: 42
Views: 1,199
Posted By Briansshop
Expensive change to make. Unless you can do the...

Expensive change to make. Unless you can do the gear change/set up yourself, it doesn't pay off from a mileage savings point of view. If you can handle the work, sure go for it.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-10-2018, 08:47 AM
Replies: 6
Views: 377
Posted By Briansshop
That sounds like the EBPV is closing.

That sounds like the EBPV is closing.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-07-2018, 09:26 AM
Replies: 11
Views: 280
Posted By Briansshop
Frustrating for sure. They wanted $400 when they...

Frustrating for sure. They wanted $400 when they first started this mess and now I just got an email offering non commercial 3rd party hosting for $99. Might have jumped on the $99 offer if they did...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-05-2018, 09:04 AM
Replies: 15
Views: 502
Posted By Briansshop
3K isn't going to get you there.

3K isn't going to get you there.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-04-2018, 11:01 PM
Replies: 8
Views: 223
Posted By Briansshop
Not the diffs specifically,but the ring/pinion...

Not the diffs specifically,but the ring/pinion gears. Very costly though unless you can do the work yourself.

Or go down to a 26" tall tire. That'd get you to about 3200 rpms at 60. But it'd be...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 02-04-2018, 09:42 PM
Replies: 8
Views: 223
Posted By Briansshop
Gear change to 4.88 or 5.13.

Gear change to 4.88 or 5.13.
Showing results 1 to 15 of 500

 
Forum Jump

All times are GMT -5. The time now is 02:55 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.