Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 15 of 485
Search took 0.43 seconds.
Search: Posts Made By: kedwinh
Forum: Ranger & B-Series 10-06-2012, 12:03 PM
Replies: 16
Views: 3,095
Posted By kedwinh
First thing I would be checking is the PCV...

First thing I would be checking is the PCV circuit. PCV valve, gasket and tubing. That's a fairly common problem on the older trucks like my 85 F150, and a cheap easy fix usually.
Forum: Ranger & B-Series 10-05-2012, 02:20 PM
Replies: 21
Views: 77,435
Posted By kedwinh
I used Motorcraft SP-432's, that's the ones the...

I used Motorcraft SP-432's, that's the ones the local Auto Zone showed as factory replacement plugs. It had E3's my son had put in it and ran like crap. The plugs were probably the biggest change I...
Forum: Ranger & B-Series 10-05-2012, 12:41 PM
Replies: 21
Views: 77,435
Posted By kedwinh
Mine is under powered but 11mpg? My 3.0 was...

Mine is under powered but 11mpg? My 3.0 was getting bad mileage when I got it back from my son but after a good tuneup and about $200 in parts it's doing 21mpg combined city/hiway. New plugs, coil...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 10-04-2012, 07:24 PM
Replies: 30
Views: 10,365
Posted By kedwinh
Thanks for the heads up but, mine already has the...

Thanks for the heads up but, mine already has the fan shroud and heavy duty radiator. That's almost a requirement with A/C out here in Arizona, so cooling shouldn't be a problem hopefully.
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 10-03-2012, 12:10 PM
Replies: 30
Views: 10,365
Posted By kedwinh
That's the way it works on ANY motor. I learned...

That's the way it works on ANY motor. I learned that years ago running 18 wheelers. You can either go up a hill with the peddle to the floor to hold speed or drop a gear, use less throttle and not...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 10-02-2012, 01:09 PM
Replies: 19,071
Views: 934,726
Posted By kedwinh
I do kind of the same thing with my shifter knob...

I do kind of the same thing with my shifter knob but I use clear silicone.
I've used it on a couple trucks and it works find. Just put some in the knob and slip it on the shifter, let it sit up for...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 10-02-2012, 01:03 AM
Replies: 30
Views: 10,365
Posted By kedwinh
Yea, the GCWR should be ok, at least as far as I...

Yea, the GCWR should be ok, at least as far as I can understand it.
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 10-01-2012, 01:34 AM
Replies: 30
Views: 10,365
Posted By kedwinh
I think the 300 would do it, just kind of think...

I think the 300 would do it, just kind of think the 351 would like it better. But I've never really pulled anything with a 351 either. I'm pretty sure I don't want a 460 mainly for the fuel mileage...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 09-29-2012, 02:22 PM
Replies: 30
Views: 10,365
Posted By kedwinh
Thanks guys. Was kind of worried about the...

Thanks guys.
Was kind of worried about the truck being able to handle it, and still am a little about the trans. But will run it and see what happens. After almost 3 million miles driving an 18...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 09-28-2012, 11:50 PM
Replies: 30
Views: 10,365
Posted By kedwinh
Pulling a 5000lb camper with an F150

Ok, I know it's been gone over before and I've done the search thing. But my question is kind of what I need to do than what it will pull.

It looks like the direction of my F150 Explorer SBSC...
Forum: Arizona Chapter 09-26-2012, 12:03 AM
Replies: 4
Views: 1,273
Posted By kedwinh
Thanks for the replies. I've been running this...

Thanks for the replies.
I've been running this through my mind for a few years now and think I'd like to learn more, and maybe even get started on the swap.
I had figured on an aftermarket harness...
Forum: Ranger & B-Series 09-24-2012, 11:23 PM
Replies: 6
Views: 833
Posted By kedwinh
Well I did a basic tuneup on the old girl,...

Well I did a basic tuneup on the old girl, plugs/wires/coil pack along with the fuel filter and the sensors I had already cleaned and she runs a LOT better. It idles smooth and no more codes, at...
Forum: Arizona Chapter 09-23-2012, 03:26 PM
Replies: 4
Views: 1,273
Posted By kedwinh
4.6 into an 85 F150?

Hey everyone.
Hope y'all are having a great weekend.
Ok, does anyone know anywhere I can check to find out what it takes to put a late model 4.6 in an older 85 F150? I've been running it through my...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 09-23-2012, 03:20 PM
Replies: 2
Views: 772
Posted By kedwinh
Don't know if I can be any help with the knocks...

Don't know if I can be any help with the knocks other than the normal recheck the timing and valve adjustment. Mostly I'd recheck the valves as that was the last thing you listed doing before it...
Forum: Ranger & B-Series 09-23-2012, 03:05 PM
Replies: 6
Views: 833
Posted By kedwinh
Thanks pawpaw When it comes to the newer EFI...

Thanks pawpaw
When it comes to the newer EFI motors I really don't have a clue most of the time. I figured there must be a way to check things out instead of just swapping parts but couldn't find...
Showing results 1 to 15 of 485

 
Forum Jump

All times are GMT -5. The time now is 07:51 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.