Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 8 of 8
Search took 0.07 seconds.
Search: Posts Made By: 49willard
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-30-2017, 09:55 AM
Replies: 452
Views: 79,307
Posted By 49willard
I have been spraying light oil on the undersides...

I have been spraying light oil on the undersides of winter driven vehicles essentially every fall for 40 years. I use 2 cycle oil since it atomizes well.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2017, 12:56 PM
Replies: 452
Views: 79,307
Posted By 49willard
I agree with Dave. I built a clone to the GM...

I agree with Dave. I built a clone to the GM Performance 383HT which dyno'ed just above factory specs. I wanted the low end torque which was 450ft-lbs but horsepower was 330 on the engine dyno. Not a...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-16-2017, 03:51 PM
Replies: 452
Views: 79,307
Posted By 49willard
Dave, I started with a pair of cherry bombs,...

Dave,
I started with a pair of cherry bombs, too LOUD. I went to a set of Borla's, much better. I was more limited by the 304 ss exhaust. When talking to a tech at Borla I explained that I wanted...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-01-2016, 06:57 AM
Replies: 452
Views: 79,307
Posted By 49willard
Dan, I can jump in here and relate my...

Dan,
I can jump in here and relate my experience with springs. My original XJ IFS came out of an early, Series 2 car. Those original springs were too soft. I purchased a new set from an ebay seller...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-07-2015, 08:14 AM
Replies: 452
Views: 79,307
Posted By 49willard
Dave, I like the Jag fuel fill, nicely done!

Dave,
I like the Jag fuel fill, nicely done!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-10-2015, 09:38 AM
Replies: 452
Views: 79,307
Posted By 49willard
Dave, Looking at your picture of the steering...

Dave,
Looking at your picture of the steering shaft/u joints what are you using for an exhaust manifold/header with the sbc? IIRC you did offset your engine to the passenger side. With a centered...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 03-17-2015, 08:14 AM
Replies: 452
Views: 79,307
Posted By 49willard
Dave, That is a bummer. Good thing that you...

Dave,
That is a bummer. Good thing that you have additional inventory!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 12-31-2014, 06:13 PM
Replies: 452
Views: 79,307
Posted By 49willard
Dave, You need to remove the "friction" bolt to...

Dave,
You need to remove the "friction" bolt to allow the mechanism to come out thru the hole. IIRC it is angled almost vertical to come out.
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -5. The time now is 12:55 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.