Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 15 of 494
Search took 0.14 seconds.
Search: Posts Made By: Rimrock F1
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-10-2017, 09:56 AM
Replies: 15
Views: 842
Posted By Rimrock F1
Very nice job. Looking great!

Very nice job. Looking great!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-04-2017, 11:07 AM
Replies: 26
Views: 816
Posted By Rimrock F1
Wow! Great looking cars and truck in front of a...

Wow! Great looking cars and truck in front of a gun store, my idea of heaven.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-23-2017, 08:23 PM
Replies: 13
Views: 588
Posted By Rimrock F1
Sorry for the delay answering, been busy. They...

Sorry for the delay answering, been busy. They told me they blast first to give some tooth. If poor quality chrome they strip first. They just blasted mine.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-20-2017, 09:15 AM
Replies: 16
Views: 634
Posted By Rimrock F1
I would break in the engine first. Here is a good...

I would break in the engine first. Here is a good article on the subject.
Engine Break-In Guide: 10 Tips to Help Properly Break in Your Engine - OnAllCylinders...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-19-2017, 09:25 PM
Replies: 2
Views: 224
Posted By Rimrock F1
Friend fabbed both and yes you are correct about...

Friend fabbed both and yes you are correct about tool steel. He and I had discussed this and I am sure that is why the weld broke. New shaft is pressed in 100 thousandths shy of flush then fully plug...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-19-2017, 09:19 PM
Replies: 13
Views: 588
Posted By Rimrock F1
Belle's new bumper

When I restored Belle I wanted to powder coat the front bumper but it had a slight amount of damage and needed filler so paint it was. Now that she has 5000 miles on her the bumper is getting a lot...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-19-2017, 08:48 PM
Replies: 2
Views: 224
Posted By Rimrock F1
Thought I was too old to drive a manual

Last Saturday the wife and I decided to go to a local car show and the wife said I could drive her 52, "Belle". When I attempted to shift into reverse to back out of the garage I had a little trouble...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-08-2017, 07:51 PM
Replies: 1
Views: 234
Posted By Rimrock F1
It is wonderful when you can enjoy the fruits of...

It is wonderful when you can enjoy the fruits of your labor. Congratulations on what I am sure was a Fantastic drive.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-03-2017, 04:13 PM
Replies: 222
Views: 45,141
Posted By Rimrock F1
The Marinco arm has a silver plastic cover over...

The Marinco arm has a silver plastic cover over the mounting end of the arm that is kind of ugly. The Trico is polished stainless, just like the look of the Trico better.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-03-2017, 04:11 PM
Replies: 222
Views: 45,141
Posted By Rimrock F1
That block is a combination valve. It does...

That block is a combination valve. It does several functions, acts a a proportioning valve to limit rear pressure to prevent rear lockup. It acts as a hold off valve so pressure starts going to the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-20-2017, 12:20 AM
Replies: 5
Views: 335
Posted By Rimrock F1
I have seen a few that have run them on the...

I have seen a few that have run them on the outside of the inner fender.

My wife's truck
...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-19-2017, 01:07 AM
Replies: 3
Views: 595
Posted By Rimrock F1
Here is a picture of mine. Only one I have as in...

Here is a picture of mine. Only one I have as in all the rest the window is always down....
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-14-2017, 08:39 PM
Replies: 112
Views: 23,116
Posted By Rimrock F1
Saw Mike's truck at a show in Payson AZ...

Saw Mike's truck at a show in Payson AZ yesterday. Beautiful!! I'm not the only one who thought so, he won 3 or 4 trophies. Congratulations mike!!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-07-2017, 09:43 AM
Replies: 17
Views: 787
Posted By Rimrock F1
Congratulations on a job well done!

Congratulations on a job well done!
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 03-24-2017, 06:19 PM
Replies: 66
Views: 5,725
Posted By Rimrock F1
Coyote in a 52. ...

Coyote in a 52.

https://cimg8.ibsrv.net/gimg/www.ford-trucks.com-vbulletin/2000x1504/80-p8200022_425383171eb78f36f19915619d920b4bbb4a55ee.jpg
Showing results 1 to 15 of 494

 
Forum Jump

All times are GMT -5. The time now is 02:56 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.