Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 15 of 298
Search took 0.58 seconds.
Search: Posts Made By: krazdndenver
Forum: Colorado Chapter 01-11-2005, 12:25 AM
Replies: 6
Views: 795
Posted By krazdndenver
Here is the story behind the engine. I built it...

Here is the story behind the engine. I built it while going to school at DADC I built the engine for the most part at the shop I work at. The heads were worked on at the school (me and the teach...
Forum: Colorado Chapter 01-09-2005, 04:29 PM
Replies: 2
Views: 463
Posted By krazdndenver
twolls, Is your friend interested?

twolls, Is your friend interested?
Forum: Colorado Chapter 01-09-2005, 04:27 PM
Replies: 6
Views: 795
Posted By krazdndenver
I have an 86 5.0L EFI fresh rebuild. For $1200...

I have an 86 5.0L EFI fresh rebuild. For $1200 You get the engine and installation. Contact me if you are interested. You can also reach me at 3037971769. Thanks Robert
Forum: Colorado Chapter 12-31-2004, 02:38 PM
Replies: 16
Views: 1,080
Posted By krazdndenver
5.0L EFI For Sale

Do you still need a V8? This is post here in the site in colorado. Please call me if you still need one.
Forum: Colorado Chapter 12-30-2004, 02:48 PM
Replies: 2
Views: 463
Posted By krazdndenver
86 302 EFI Engine

I built this engine some time ago for my 72 F100 and it ran fine(less then 1 hour run time on complete rebuild-lots of time and a bit of money) but then I decided to go a little crazy with the truck...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 10-24-2004, 06:32 PM
Replies: 2
Views: 329
Posted By krazdndenver
contact me off list, I may be able to help you ...

contact me off list, I may be able to help you
Robert - [email protected]
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 08-26-2004, 07:05 PM
Replies: 3
Views: 418
Posted By krazdndenver
My guess is that it should be for the most part a...

My guess is that it should be for the most part a easy job, if you have a 302 in the truck. I dont think trannies fit 302 and 360/390. I use to have a 4 speed in my 70 but now use an AOD. As far as...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 08-21-2004, 10:52 PM
Replies: 4
Views: 506
Posted By krazdndenver
Get all that you are looking for and some with a...

Get all that you are looking for and some with a mustang II kit. I have installed a fat man fab. stage two kit and this not only looks great but will perform great also. It is a bit pricie but you...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 08-14-2004, 09:52 PM
Replies: 4
Views: 344
Posted By krazdndenver
I would start by checking for power out at the...

I would start by checking for power out at the turn signal switch connection both sides of it and then work out ward from there. This is assuming you have checked the bulbs and the ground connections...
Forum: Electrical Systems/Wiring 08-11-2004, 06:33 PM
Replies: 6
Views: 354
Posted By krazdndenver
it sounds like a broken turn signel switch....

it sounds like a broken turn signel switch. Replace that and the rod will screw in.

Robert
72 F100
www.geocities.com/krazdndenver
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 08-08-2004, 05:04 PM
Replies: 2
Views: 204
Posted By krazdndenver
when i did this swap some time ago i moved...

when i did this swap some time ago i moved original 360 perches back to the other set of holes, same thing you see, engine to close, then moved them back to stock location and it fit great, the...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 08-03-2004, 02:17 PM
Replies: 4
Views: 908
Posted By krazdndenver
Well it has been installed and all went well....

Well it has been installed and all went well. There are pics at www.geocities.com/krazdndenver . Now the truck is bare frame, did some other work like taking out 16" of frame in the rear to get a...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 07-05-2004, 11:56 PM
Replies: 1
Views: 281
Posted By krazdndenver
new web page

I finally got around to getting a better page built. So instead of going to the shop and working on the truck I decided to work on the page that shows the accomplishments and to share information. It...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 07-05-2004, 11:51 PM
Replies: 14
Views: 696
Posted By krazdndenver
Also don't cut the frame up and down. The best...

Also don't cut the frame up and down. The best way is fish mouth but I did mine on a 45^ angle
Robert
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 07-05-2004, 02:52 PM
Replies: 14
Views: 696
Posted By krazdndenver
I did this a week ago, You have to cut 16" out of...

I did this a week ago, You have to cut 16" out of the frame between the end of cab and front of axle, you also need to cut 3.6" out after the axle. I did not perform the second because of my fuel...
Showing results 1 to 15 of 298

 
Forum Jump

All times are GMT -5. The time now is 07:56 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.