Ford Truck Enthusiasts Forums - View Profile: epp

epp is gaining momentum as a positive member of FTE.

epp epp is offline

Senior User

About Me

  • About epp
    Del City, OK
    2 Letter State/Province (use "--" for outside USA/
    Country of Residence
    F-1 through F-8
    Current Mileage
    Rather not say
    Miles per year
    Rather not say
  • Signature
    '50 F1 454/400 - Built the way I want it.
    '13 F150 FX4 5.0
    '10 HD FLHXXX
    No trees were killed in the sending of this message. However a large number of electrons were terribly inconvenienced


Total Posts
Visitor Messages
General Information
  • Last Activity: 02-17-2019 11:08 AM
  • Join Date: 02-06-2010
  • Referrals: 0


Showing Friends 1 to 1 of 1

Visitor Messages

Showing Visitor Messages 1 to 10 of 14
  1. 05-28-2013 08:56 AM - permalink
    My name is Timoteo Salinas, and i'm starting to plan my rebuild of my 52 f1. I am currently living in Ft. Sill, OK. I was wandering if you would be able to help me out with the planning on the engine rebuild and locations of some good engine machine shops. I have some ideas but need to knowledge and experience on flathead V8s. I would appreciate your help. My email is [email protected]
  2. 04-02-2013 10:34 AM - permalink
    Could you also send me the documents on the tilt front end, please. I'm looking into doing one and just want to see what kind of headache I'm getting into. Thanks, Terry. [email protected]
  3. 02-24-2013 02:46 AM - permalink
    Hey do you have that front end up write up?
    [email protected]
  4. epp
    08-29-2012 11:17 AM - permalink
    Mine is installed pretty simple. It has a frame around the grill area that goes down to 2 arms that face towards the front of the truck. two holes in the frame which is where the arms bolt to and pivot off. If yours is the same, set it on the truck, make sure you have it exactly where you want it and mark the spots on the frame, drill holes and put your pivot bolts in, done. Its really simple vs welding up the sheet metal front end and then making it pivot.
  5. armyaviation
    08-27-2012 08:28 PM - permalink
    I am new to the forum and read your post about your fiberglass front end. I have a fair lane for my 1956 that I am about to install. Do you have any advice, thanks, tom
  6. 08-07-2012 09:11 PM - permalink
    i think tilt fronts are way cool and am looking for
    all information i can get-not much out there-please
    send me your docs
    [email protected]
    i am new here- and hope this is how to ask for the information
  7. Samsn4
    02-23-2012 05:15 PM - permalink
    could you pass on the Doc about the tilt front end ? Thanks

    [email protected]
  8. 07-31-2011 09:37 PM - permalink
    Are you on the HAMB or on the Okie HAMB group?
  9. epp
    12-17-2010 04:10 PM - permalink
    anytime glad to help
  10. 12-15-2010 09:28 AM - permalink
    Thank you very much for taking the time to go out and take those measurements for me, much appreciated. regards Mark

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.