Ford Truck Enthusiasts Forums - View Profile: SkySkiJason

SkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant futureSkySkiJason has a brilliant future

SkySkiJason SkySkiJason is offline


Visitor Messages

Showing Visitor Messages 1 to 10 of 104
  1. MoBill122
    09-20-2017 08:41 AM - permalink
    What you charge to run a scan on my truck... just look it over and make some recommendations of what may need to be done to it. Its mostly stock and I'm not wanting to change it all up.... but with the miles, I know there's things that I need to start looking closer at.
  2. Keabler
    08-20-2017 10:12 AM - permalink
    I'm sort of worried about used rear ends, though that is about 1500 cheaper than rebuilt. I'm also on the other side of the country, though I own a house in Savanah.
  3. death_4u
    05-22-2017 06:53 PM - permalink
    Do you happen to still have the pictures of where the brackets go? How thick is the fiberglass?
  4. death_4u
    04-30-2017 03:27 PM - permalink
    I'm looking at the mcneil 2016 super duty front end kit, but can't find any information on it or how to install. Did everything just bolt together in the factory holes, or were modifications needed? Does it work with the 99-07 factory wiper cowl?
  5. AllaboutMPG
    05-08-2016 08:07 AM - permalink
    Thanks for the reps. Just trying to help were i can, a little payback for all I've gotten from the brotherhood. Hope to come see you some day since we're not too far apart. May even talk to you about a freshen up rebuild on my motor. Paul
  6. mueckster
    05-29-2015 05:47 PM - permalink
    Thanks for the reps, Jason! Hope you and the boys are doing great.
  7. F250_
    05-27-2015 09:10 AM - permalink
    Thanks, Jason... hoping to get some good info to finally get real answers for all of us.
  8. Christof13T
    06-29-2014 09:39 AM - permalink
    Dangit Jason! Your pm box is full lol
  9. truck7575
    04-14-2014 01:24 AM - permalink
    i saw your name mentioned in a post as being really experienced at pulling a 7.3 out of an excursion. Let me give you a little background on my situation.. I have an 2003 X and I have a timing cover that needs to be replaced, the mating surface for the water pump has completely corroded away and i can no longer get it to seal. I realize this means the timing cover needs to be replaced.. I know this requires at minimum lifting the engine but to be done right i need to pull the engine. I have 315000K Miles and it runs great! I have rebuilt everything on top of the motor and now it looks like im gonna need to pull the motor, while out i was gonna swap in a reman motor and heads just cause the job is so big. My question to you is what all needs to come off of the top of the motor in order to pull it out if i remove the front of the truck. Any advice for this job, any pictures you may have? What all actually needs to come off of motor to get it out? Thanks Rick
  10. glockholiday
    01-11-2014 05:27 AM - permalink
    This is regarding a post of yours in 2011 about your 255/85/16 Toyo M55 tires.

    I've got a 2002 F350 CC Dually 4x4 with 265/75/16's on it now and they are a little too wide for the rear but I'm going to wear them out.

    My next tires I would like a little taller, and since I don't want to listen to a BFG mud terrain I'm going with the Toyo's. To my question, is your truck any higher than stock, friends are telling me the 255/85/16 might rub in the front when turning, I don't think so but you're the first person I've found with them to ask, any rubbing?

About Me

  • About SkySkiJason
    perpetual tinkerer - travel all over US for work
    N.GA Mountains
    (2) boys in elementary school, Hydrofoil Water Ski (Sky Ski/Air Chair), camping, hiking and VO for fuel!
    2 Letter State/Province (use "--" for outside USA/
    Country of Residence
    Current Mileage
    250,000 or more
    Miles per year
    50,000 - 74,999
  • Signature
    2001 F350 CC flatbed - headstuds, AC codes, T4/S366, custom leather interior, '07 facelift, big honkin bumper, 180k miles on DIY veggie conversion and a few other things...
    2000 Excursion, Limited, 4x4, BTS trans, 120k on veggie! - wrecked spring 2013 - RIP authorized installer


Total Posts
Visitor Messages
General Information
  • Last Activity: Yesterday 07:07 PM
  • Join Date: 07-30-2008
  • Referrals: 2


Showing Friends 1 to 10 of 26

All times are GMT -5. The time now is 04:24 AM.