Ford Truck Enthusiasts Forums - View Profile: smoky_diesel

Notices
smoky_diesel is a splendid one to beholdsmoky_diesel is a splendid one to beholdsmoky_diesel is a splendid one to beholdsmoky_diesel is a splendid one to beholdsmoky_diesel is a splendid one to beholdsmoky_diesel is a splendid one to beholdsmoky_diesel is a splendid one to behold

smoky_diesel smoky_diesel is offline

Posting Guru

About Me

  • About smoky_diesel
    Biography
    Ford Scientist
    Location
    Chandler, AZ
    2 Letter State/Province (use "--" for outside USA/
    AZ
    Country of Residence
    US
    Make
    Ford
    Model
    F-250
    Year
    2014
    Current Mileage
    25,000 - 49,999
    Miles per year
    1,000 - 4,999
  • Signature
    Justin
    2014 F-250 Lariat CCLB 6.7 - Kodiak Brown, 3.55e, Amp steps, 3.5" lift w/ custom air bags, 37/12.50 Toyo MTs 20x9 BMF. sub, amp. Lance 815, 23ft Baja 7.4mpi, Titan 3H slant
    1972 F-250 Explorer 390/C6 2WD to 460/C6/NP205 D60/10.25 4WD - in progress
    2004 Cobra 'Commuter'. Blown, nitrous, 580 wtq MT drag radials, 1kw audio system
    2009 Yamaha Raider - 113 ci, 96whp/117wtq

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: Yesterday 11:25 AM
  • Join Date: 09-25-2007
  • Referrals: 0

Visitor Messages

Showing Visitor Messages 1 to 7 of 7
  1. lindner115
    10-31-2016 03:02 PM - permalink
    Hey Lindner115 again, sorry to bother you again. I was wondering after looking at all the aftermarket radius arms, they only slot lower hole. Can i get away with doing this only? i am putting the truck on alignment rack tomorrow to get rock solid caster number. Would like to get to the 4 degree area. Say i'm at 1 degree positive, how far in what direction do i slot to gain 3 degrees? Does this make any sense.
  2. lindner115
    10-31-2016 01:59 PM - permalink
    Hey i seen your right up on modifying your radius arms on f350. I've got same issue and am throwing around doing that. Was it much a job to get them out? The top hole goes forward and bottom goes back, it that correct or other way around? How far did you go about a 1/4"? thanks.
  3. 07-14-2016 12:42 PM - permalink
    I posted pics of rear end , see what you think its on the thread you replied to
  4. 01-01-2015 02:25 AM - permalink
    What kind of fender flares are those? They seem lower profile than most. Thanks
  5. 11-18-2014 12:17 AM - permalink
    Is your rear sway bar setup still available? If so, I would be happy to pay shipping and a boxing fee for it. Would be installing on my 2014 f250 ASAP. Let me know.
    Thanks
    Eric
    Can email me at [email protected]
  6. 03-20-2014 09:25 PM - permalink
    Any chance you could make another? Let me know, thanks.
  7. 02-17-2014 08:20 AM - permalink
    Justin,
    I saw your post of the front hitch you made and its perfect. Ive got a 2012 F250 and cant find anything that fits as well as your custom job. So my question is, care to make another? I have zero welding skills and don't think the welders I know would match what you've done.

    Best Regards,
    Nicholas

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.