Ford Truck Enthusiasts Forums - View Profile: AXracer

AXracer has much to be proud ofAXracer has much to be proud ofAXracer has much to be proud ofAXracer has much to be proud ofAXracer has much to be proud ofAXracer has much to be proud ofAXracer has much to be proud ofAXracer has much to be proud of

AXracer AXracer is offline

Post Fiend

About Me

  • About AXracer
    Durham NC
    2 Letter State/Province (use "--" for outside USA/
    Country of Residence
    Current Mileage
    Rather not say
    Miles per year
    Rather not say
  • Signature
    Passionate about autocross racing!

    1956 F100 Panel "GRACIE"
    2007 Solstice GXP racer, the "KRAZED KANARY"
    Third place finish 2009 SCCA National Championships


Total Posts
Visitor Messages
General Information
  • Last Activity: 01-02-2018 12:17 PM
  • Join Date: 10-19-2004
  • Referrals: 0

Social Profiles

Instant Messaging
Send an Instant Message to AXracer Using...
This Page


Showing Friends 1 to 10 of 24

Visitor Messages

Showing Visitor Messages 1 to 10 of 38
  1. underthebridgejim
    11-02-2015 12:17 AM - permalink
    Chuck, I wanted to thank you for the rep you have sent my way, its very much appreciated.
  2. 56panelford
    09-13-2015 08:45 AM - permalink
    Nobody has a bigger ego than you and if someone isn't stroking it for you ,you do it yourself.
  3. flattie39
    08-27-2015 12:51 PM - permalink
    Thanks for the info Ax - I really don't know but I've always thought it was a 1/2 ton. I'll check with the MF catalog and see if I can tell which leafs I still have and go from there. Thanks again, Ken
  4. flattie39
    08-26-2015 08:06 PM - permalink
    Hey AX - My 54 still rides really stiff in the back, even after the PO removed 5 of the leafs. Can I make a softer ride in back by removing more leafs, and if so, which ones? I don't use it for hauling anything. Ken Clark (former welding classmate)
  5. schoo
    01-15-2015 03:19 PM - permalink
    hi ax can you send that hammer profile to me
    thanks roy email= [email protected]
  6. underthebridgejim
    12-09-2014 01:38 AM - permalink
    Your advice is much appreciated. PS. I just ordered a 4 1/2" shrinking disc from Wolfs, I think it may just do the trick. It may be awhile B4 I get to it, my Rheumatoid A. and the cold don't go well together, but I will. LOL, I always do eventually.
  7. underthebridgejim
    12-07-2014 03:44 PM - permalink
    I just ordered an 11lb spool of ESAP .023 easy grind. Thanks for the tip.
  8. AXracer
    11-24-2014 10:08 AM - permalink
    I know nothing about PS pumps on flatheads, and not a whole lot more about flatheads in general much beyond how to swap them out for a modern V8. Sorry
  9. 11-23-2014 08:30 AM - permalink
    Hi AXracer
    I am doing the Toyota power steering on my 1950 F1 pickup.
    Do know what PS pump was used in the Brundell flathead conversion.
    Any help you can give me would be great.

  10. 54-F100
    11-21-2014 10:52 AM - permalink
    Hi AXracer,
    I was reading through a post where someone commented that you had made a post along the lines of "How to align a 53-56 F100 front end clip".
    Well I didn't want to bother I went 'stalker' and flipped through a few hundred of your posts with absolutely no luck - I did learn about several things to consider in the life of our own build for our 54 F100 :-)
    Do you know where I might find some good instructions on bringing my front fenders & hood into the best alignment?

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.