Ok, the other was getting pretty long, and needs refreshed, so here we go again. It is asked that this thread be used only for posting the sale items or wanted items, discussion needs to be either by email or by the FTE Private messaging system please.

 

77 Yamaha GS(?)750 triple

We (my wife and I) put a new head gasket in it this winter, and now we can't get the darn thing to start. It is electrical because we are not getting any spark.


I am tired of messing with it and will take $100.00 OBO. Plus I am buying a newer one and need it out of the garage..


MUST SELL!!

Email me for pix

 

76 Ford F250 4x4 (Highboy) 390 only 40k on motor, 4spd Brand new clutch, 33x16.50 tires

Comes with extra Dana 44 front axle (needs new gears, but still has the brakes and tie rod on it)

I need to sell this ASAP as I am in desperate needs of some cash.

Best Offer

If you would like pictures I can email them to you.

Matt

 

Ok I got an injector pump(7.3)- a set of heads(7.3) - injector lines - intake- exhaust manifolds- starter-2 alternators-off a 1986 or 1992 diesel. a bronco II drive shaft (rear) with u joints. all for sale shoot me a price.for any or all.

 

Need a 1.31 or 1.33 ford 2v carb- these were used on some 429's and larger trucks and buses I'm told. To identify, look for the number on the drivers side of carbs float bowl, the number will be kind of blocked by the accelerator pump linkage rod, but should still be fairly easy to see.

 

ive got (2) two np 208 transfer cases for sale. make an offer. also, my 88 is for sale, check my gallery for pics. feels like its stuck in 2 low.

 

Well I have several things that I would sell don't need to but if I have something someone needs it's always for sale so I will make a short list.
9" gears 5.00:1, 3.25, and possibly a set or 2 of 3.50
D44 rev cut gears 4.88, 3.08, 3.50
also have a D44 solid axle, and ford 9" complete out of a 78 bronco both with 3.50 gears
3 C6 trannies 1 short shaft 4x4, 1 medium shaft 4x4, and one long shaft out of a van, I consider them all cores although I was told when I picked them up that they all worked.
also have a set of used SBC 6" Hbeam rods that were used in a 393 windsor.
850cfm barry grant mighty demon
couple of 9" dropouts
3 np205 transfer cases all good
78-79 ford F150 4x4 powersteering box that I think should have a kit put in it.
holley red elec fuel pump used
302 edelbrock performer rpm intake
misc sbf engine parts like cranks heads etc just ask
elec water pump, and gear drive starter for a small block ford
afco alum radiator out of a late model modified stock car
well thats mostly what I can think of off hand.

 

lookin for a driverside door and fender for my 88, and a borg warner t case

 

I need a SOHC motor for a 1999 or earlier Dodge/Plymouth Neon. Head gasket is letting go and the top end is getting noisy. Damn Dodges! This POS engine has been noisey since it had 35k miles on it...always ticking at startup and quieting once warm....110K on it now and it is getting louder and leaking oil out of the rear of the head gasket. So I need a donor engine or head to swap out once she takes the dirt nap. Would consider a complete parts car, complete engine or parts. Let me know!

 

I have a brand new 12"clutch, throw out and pressure plate as well as a good fork, boot, and bellhousing for a 351m, 400, (and big blocks??) Would like to trade for a good small block AOD or possible a C6 or ?? e-mail me with trade or cash offers. thanks.

 

im looking for a center console lid for my f150..all i need is the lid ill use my leather i have know....can anyone help me out.... thank you alan

 

<TABLE cellSpacing=0 cellPadding=0 width="100%" border=0><TBODY><TR><TD></TD><TD class=classieAdTitle align=left colSpan=3>77 Ford F250 (Trucks) </TD></TR><TR><TD></TD><TD class=classieAdBody colSpan=3>Super Cab 460 V-8 4bbl C6 Auto rear 3.54 8' bed, cold a/c, cruise, 8100 Max GVWR 6 good tires all great tread, some rust, $1800, 610-0097 </TD></TR></TBODY></TABLE>
http://home.mchsi.com/~shaneandchari...s/DSC00013.jpg

 

FOR SALE:make a reasonalbe offer
-Front suspension from a 54 Ford F100 half ton, everything from the springs to the drums
-Radiator from a mid-80s chevy pickup
-stock 289 exhaust manifolds...mustang
-AOD Tranny...84 Lincoln town car
-302 block from an 84 Lincoln town car
-302 heads from an 84 Lincoln town car
-NUMBERS MATCHING COMPLETE..needs restored 69 Roadrunner....$5,000
-69 Roadrunner frame and body....$2,500
-69 Roadrunner frame, body, rolling chasis......$3,000

 

lookin for a solid axle for my 88 right now. kinda on a budget, so not sure what im gonna do, but still lookin. need a window crank for my window too.

 

hello everyone,
i was wondering if anyone know of a 1972ish Ranchero hood for sale. i'm looking for the one with the hood scoop, the same one that fits a 1972 torino. i'm located in iowa, and it knida needs to be nearby, because i don't think anyone will ship it for a decent cost. i wouldn't mind driving for a little ways, but i'm not going to texas to get a hood.
thank you,

Lee