4r100 Speed Sensor Tone Wheel Install on Vehicle?
#1
4r100 Speed Sensor Tone Wheel Install on Vehicle?
Hello.
I have a 99 F350SD. It has a 4x4 4r100 in it. It puked its guts out. I managed to find a 4x4 4r100 out of an E450 with about 12k miles on it. And I was going to install that into my truck until I realized it appears to not have an output speed sensor tone wheel on the output shaft.
I was trying to find out, is there a way to press or put the tone wheel onto the new(er) transmission without a complete teardown and rebuild. I have the OTC spacer tool, and all, I just wasn't sure if anyone has done it. Or, is there a bolt on/slip collar type of assembly that can be added aftermarket? I saw a picture of this, no idea if it would be something i could use.
Thank you for your time.
I have a 99 F350SD. It has a 4x4 4r100 in it. It puked its guts out. I managed to find a 4x4 4r100 out of an E450 with about 12k miles on it. And I was going to install that into my truck until I realized it appears to not have an output speed sensor tone wheel on the output shaft.
I was trying to find out, is there a way to press or put the tone wheel onto the new(er) transmission without a complete teardown and rebuild. I have the OTC spacer tool, and all, I just wasn't sure if anyone has done it. Or, is there a bolt on/slip collar type of assembly that can be added aftermarket? I saw a picture of this, no idea if it would be something i could use.
Thank you for your time.
Last edited by zer0_13; 11-09-2018 at 07:13 AM. Reason: adding picture
#2
Hello.
I have a 99 F350SD. It has a 4x4 4r100 in it. It puked its guts out. I managed to find a 4x4 4r100 out of an E450 with about 12k miles on it. And I was going to install that into my truck until I realized it appears to not have an output speed sensor tone wheel on the output shaft.
I was trying to find out, is there a way to press or put the tone wheel onto the new(er) transmission without a complete teardown and rebuild. I have the OTC spacer tool, and all, I just wasn't sure if anyone has done it. Or, is there a bolt on/slip collar type of assembly that can be added aftermarket? I saw a picture of this, no idea if it would be something i could use.
Thank you for your time.
I have a 99 F350SD. It has a 4x4 4r100 in it. It puked its guts out. I managed to find a 4x4 4r100 out of an E450 with about 12k miles on it. And I was going to install that into my truck until I realized it appears to not have an output speed sensor tone wheel on the output shaft.
I was trying to find out, is there a way to press or put the tone wheel onto the new(er) transmission without a complete teardown and rebuild. I have the OTC spacer tool, and all, I just wasn't sure if anyone has done it. Or, is there a bolt on/slip collar type of assembly that can be added aftermarket? I saw a picture of this, no idea if it would be something i could use.
Thank you for your time.
#3
I believe you can press it on, but you do surely need that spacer, if it isn't lined up obviously you will have issues. Not sure if you would be able to press it on without taking it out of the trans? I needed one with a tone wheel also for my 4x4 conversion, but I got it on ebay for like 60 bucks, but I am also rebuilding the trans, so it was easy to swap output shafts.
Thread
Thread Starter
Forum
Replies
Last Post
Expy250
Clutch, Transmission, Differential, Axle & Transfer Case
6
05-19-2020 10:45 PM
Dutter 2
1997 - 2003 F150
2
10-12-2013 02:28 PM