1956 F100 Crew Cab Project Started - LOTS OF PICTURES - Page 25 - Ford Truck Enthusiasts Forums



1948 - 1956 F1, F100 & Larger F-Series Trucks Discuss the Fat Fendered and Classic Ford Trucks

1956 F100 Crew Cab Project Started - LOTS OF PICTURES

Reply
 
 
 
Thread Tools Search this Thread
  #361  
Old 01-06-2018, 07:59 PM
EffieTrucker's Avatar
EffieTrucker EffieTrucker is online now
Kentucky Chapter Member
 
Join Date: Jan 2011
Location: Eastern Kentucky
Posts: 2,505
EffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud ofEffieTrucker has much to be proud of
Thank you! I know itís a lot of work, and it is appreciated.
Reply With Quote
  #362  
Old 01-08-2018, 05:45 PM
Olboy's Avatar
Olboy Olboy is online now
Junior User
 
Join Date: Oct 2017
Posts: 53
Olboy is starting off with a positive reputation.
Dynamic - what a great thread.

Originally when I started reading this thread, I thought to myself 'another big idea that won't get completed...' but you sir have made huge strides. Then I saw that you rebuilt the original master cylinder and I thought to myself 'that's going to suck with the factory brakes and original running gear...' then the crown vic showed up and you got my attention. I also now understand why you bolted the 2 frame sections together instead of welding, this way you could adjust to fit the cabs - also a great methodology. When I first saw that it was spliced together with 3/8" bolts I was dubious.

I got a 2007 P71 Crown Vic over the holidays and plan to do the suspension and power train swap as you did but I am going to keep the automatic transmission. I have put nearly 1000 miles on the cop car and it runs excellent and has plenty of 'jam' especially considering my 53 Merc M-100 weights ~1000 lbs less than the crown vic does. I like the simplicity of the way that you mounted the front end and will likely do something similar. Are you happy with the front end height? Why do you think the driveshaft interfered with the cross member? I haven't heard of people having this issue before but then no many people run the crown vic / 4.6 engine mounts with the front end swap. Do you plan to C-notch the rear? Are you going to run an explorer rear diff or narrow yours or widen your rear fenders?
Reply With Quote
  #363  
Old 01-13-2018, 04:17 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
Quote:
Originally Posted by Olboy View Post
Dynamic - what a great thread.

Originally when I started reading this thread, I thought to myself 'another big idea that won't get completed...' but you sir have made huge strides. Then I saw that you rebuilt the original master cylinder and I thought to myself 'that's going to suck with the factory brakes and original running gear...' then the crown vic showed up and you got my attention. I also now understand why you bolted the 2 frame sections together instead of welding, this way you could adjust to fit the cabs - also a great methodology. When I first saw that it was spliced together with 3/8" bolts I was dubious.

I got a 2007 P71 Crown Vic over the holidays and plan to do the suspension and power train swap as you did but I am going to keep the automatic transmission. I have put nearly 1000 miles on the cop car and it runs excellent and has plenty of 'jam' especially considering my 53 Merc M-100 weights ~1000 lbs less than the crown vic does. I like the simplicity of the way that you mounted the front end and will likely do something similar. Are you happy with the front end height? Why do you think the driveshaft interfered with the cross member? I haven't heard of people having this issue before but then no many people run the crown vic / 4.6 engine mounts with the front end swap. Do you plan to C-notch the rear? Are you going to run an explorer rear diff or narrow yours or widen your rear fenders?


Olboy, Thanks for the kind words.


Things have been slow the past year or so due to just simply too many projects. I actually worked on the truck a bit today, but nothing to really show or talk about.


I suspect the interference I had with the cross member is due to my transmission choice, coupled with the height I set the cv suspension in the 56 suspension.


The truck is currently sitting on a explorer disc rear end. Right now no C notch is in the plans. But once its a running driving vehicle I may decide to put in the four link I was planning on. At that point the c notch will be required.
Reply With Quote
  #364  
Old 01-13-2018, 06:37 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
so.... I haven't made any of the progress.... due to the pictures being messed up by photobucket.


now that I have them all updated and visible, here is some of the progress you missed.


I was able to get the pedal box all tacked up and tested.
















Reply With Quote
  #365  
Old 01-13-2018, 07:03 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
Broke out the made in Taiwan inner fenders.





As you can see there are some reinforcements on the original fenders that were not duplicated on the aftermarket duplicates.


You will also come to find that all the bolt holes don't line up. That the pieces may be slightly different than your originals. That they are much thinner than the stock pieces.







marked them using the original fenders I already cut as a template and cut out the openings for the crown vic suspension.







Reply With Quote
  #366  
Old 01-13-2018, 07:40 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
started installing the dieted crown vic wiring harness.




bolted both sets of harness' together at the firewall.


then ran them under the dash to start routing them.










Hung the fuse panel in approximately its new location








Ran all these under the dash to the center and over to the passenger side kick as needed.










The wiring that will be heading to the back of the truck for things like window switches, tail light wiring, fuel pump, etc were all ran to the center of the dash so it could be hidden under the center console and dropped thru the floor.
Reply With Quote
  #367  
Old 01-13-2018, 07:44 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
Made a simple bracket for the fuel line an fitting to mount to the chassis. Cut a section of fuel line. installed the an fittings and ran the line to the fuel rail.




Reply With Quote
  #368  
Old 01-13-2018, 07:51 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
Flared some brake lines and ran them from the proportioning valve to the front wheels.










Reply With Quote
  #369  
Old 01-13-2018, 07:57 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
decided to run the stock air box, so I had to cut a hole in the inner fender for fitment





that will work



Going to have to cut a new hole for the air intake, and extend the rubber tube to the headlight/grill support.

Reply With Quote
  #370  
Old 01-13-2018, 08:13 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
Ran the wiring for the lights, horn, electric fan, and other components down the inner fender and up around it.

I cannot remember what the hell bolts to the lowest hole on the inner fender.

Can some one post a picture?




wires run high up under inner fender.





Had to make a transition from inside the inner fender to across the front of the truck. I didn't want to see any wires behind the grill other than needed wires. so...





I cut a hole at the bottom of the inner fender where the front cross member is. This area will be covered with the new radiator support hanger bracket.





wires run thru hole heading to passenger side mirrored hole.




Under hood fuse panel will go on passenger fender. Just have to decide where.




Reply With Quote
  #371  
Old 01-13-2018, 08:16 PM
dynamic's Avatar
dynamic dynamic is offline
FTE Chapter Leader
Thread Starter
 
Join Date: May 2001
Location: Rhode Island
Posts: 2,962
dynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to beholddynamic is a splendid one to behold
The ecm found itself a nice home


fits well where it is. just need to modify the stock bracket.

Reply With Quote
  #372  
Old 01-13-2018, 10:33 PM
Ken Newman's Avatar
Ken Newman Ken Newman is offline
Senior User
 
Join Date: Nov 2010
Location: Queen Creek AZ
Posts: 215
Ken Newman has a good reputation on FTE.Ken Newman has a good reputation on FTE.
Looking great. Keep the pictures coming. Glad you are making good progress.
Happy New Year
Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Dash Bezel, Gauges and parts buckin69bronco Ford Truck Parts for Sale 3 08-02-2017 06:18 PM
Back in the Saddle Again Dman130 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 8 06-02-2017 09:32 AM
Anyone got a crankshaft pulley? 1952 Ford 1948 - 1956 F1, F100 & Larger F-Series Trucks 21 01-19-2017 12:44 AM
1 ton Ford tailgate (55") SOLD chriscris Ford Truck Parts for Sale 4 11-25-2016 06:46 AM
Rear Brake Caliper damage BlackTruckDave 1999 to 2016 Super Duty 5 10-19-2016 01:23 PM


Go Back   Ford Truck Enthusiasts Forums >

Tags
1956, 56, buddy, cab, cabs, crew, double, f100, fioo, fire, maryland, md, pictures, sale, truck

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -5. The time now is 08:44 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.