Category: Exterior - Body Parts
Price: $1
Private or Vendor Listing: Private Listing
Part fits (you may select multiples): '92+ Civic/EL & Del Sol, Prelude
Engine: Part suitable for gas truck

Hello,

I have a 66 ford cc. I am in need of a hood. How much are you asking for yours? I live in Wa. state. Thanks

 

camperspecial65',

The mirror arm I am looking for is the standard truck mirror. It is approximately 10 1/2" long, 3/4" round, with approximately the last 1" of it square where the mirror head bolts through. Have everything but the arm, let me know what you got.
Thanks,
Joe
shovhedjoe@aol.com

 

do you have a 73-79 transmission tunnel cover? Preferably from a automatic. Shipped to 29169. Thanks!

 

cs65, I just bought a 63 f100 that has had a lot of work done before I picked it up. One problem area it has is the hood. It's been bondo'ed in several areas, and should really be replaced. If you would have one, or able to get a good replacement, I would like to get one. My e-mail is gadden2@grics.net If you think you might be able to help, please drop me line. Thanks... Mike

 

Looking for a solid set of FE exhaust manifolds for my 65. I'm just a few miles north of you in Sedro Woolley, 98284.
thanx

 

intake for a 300 straight 6?

 

Do you have any Front bumper mounts for a 1975 F-250 Highboy?

 

Was after complete tail lights for a 65 styleside??

 

66 Ford CC, Slow Joe, jbouknight, Mike Gadden, rogue40, samsn4, 1977 Mud Rat...I dont have any of those items you are inquiring about...

muzza279, are you seeking the lenses or lenses and tail light door or those along with the light bulb socket/body thats screwed to the bed ??


I have lenses and Im pretty sure I have the t/l door...I would need to check on the t/l body though...



- cs65

 

tanman722...I have all of those items...the t/gate trim panels...the large upper panel around the handle area with the black finish..the heavy puppy..I also have the nameplate finish panel...driver quality though..

kylesandy64..I do have the dentside dashpad in black..


scott79, I will need to double check on the door panels...i think i do but want to verify the upper trim version..


As for prices, PM or email me direct for fastest replies as the mailbox fills fast...


- cs65

 

Yeh after both body and lense, mainly after the body though

 

parts update...


dentside guys...I have a couple of gems...lighten visor vanity mirror with the LH mate in black...with the wire that runs down the A pillar.

I also have a 3 spoke Sport steering wheel with center button in very nice condition..not perfect, but material is all there...

transfer case boot trim ring...no broken tabs and in super shape..tough to find as the tabs are prone to breaking off...



61-66 guys...I have some goodies fresh from the dry desert...aluminum scuff plates...61-64 deep step type...Ive not seen a pair this nice yet...


I also have a super rare find...a CORRECT factory power steering automatic steering column...turn signal switch is gone and it has a later type shift lever this is for 65-66 trucks ONLY as the steering shaft is slightly different in length in the bumpside trucks.


I am out of sheetmetal totally except a LH 61-66(correct holes for 65-66) fender in OE Wimbledon white...excellent paint...fender has slight pancake...hard to spot unless you are looking for it...zero rust in the typical areas..i.e., no rot...
I also have tailgates in various conditions...80-86/7(?) Flareside in white...excellent condition...wax and use as it...several 64-66 correct type gates for Styleside and a 57-66 single wall Styleside bed gate in very very nice condition.
Door glass for 61-66 as well as vent glass in bad frames...free to good home...just pay shipping...




- cs65

 

muzza...check back tomorrow...or leave a visitor message in my 'profile' on here...click my nick and leave a message..email addy and I can reply that way.


- cs65

 

looking for a complete cruise control setup. what are you wanting out of the sport wheel and the vanity visor.

 

PM sent choptop...


- cs65