Technical Service Bulletins
|Publication Date: May 13, 2003|
1997 F-250 LD
1998-1999 E SERIES
2000-2001 SUPER DUTY F SERIES
Article 02-10-5 is being republished in its entirety to update the model line and model year coverage.
Some 1996-2002 Bi-Fuel CNG F-150, E-250/350, 1996-2000 Contour, 2000-2003 Bi-Fuel LPG F-150 and 2000-2001 Super Duty F Series vehicles (without coolant lock-off) may exhibit a no start condition. This may be caused by stuck Low Flow Injectors on the Compuvalve possibly due to fuel contamination. To avoid the replacement of the Compuvalve when only the Low Flow Injectors have failed, the Low Flow Injectors have been released separately for service.
If diagnosis leads to a failed Low Flow Injector, refer to the following removal and installation procedure to replace the Low Flow Injector assembly.
|WARNING:||WHEN SERVICING FUEL RELATED COMPONENTS, ELIMINATE ALL SOURCES OF IGNITION (E.G. TORCHES, HEATERS, AND LIGHTED TOBACCO). FLAMMABLE MIXTURES MAY BE PRESENT AND CAN IGNITE, RESULTING IN DAMAGE AND/OR INJURIES. THE FUEL SYSTEM LINE PRESSURE MUST BE RELIEVED BEFORE ANY COMPONENT CAN BE REMOVED. REMOVAL OF COMPONENTS WITHOUT PRESSURE RELIEF CAN CAUSE AN UNCONTROLLED RELEASE OF PROPANE OR NATURAL GAS AND MAY RESULT IN DAMAGE AND/OR INJURIES.|
- Relieve system line pressure and remove the Compuvalve from the vehicle. Refer to Service Manual GFIP162 for the 1996 CNG Bi-Fuel model year and Service Manual GFIP173 for the 1998 CNG Bi-Fuel model year. Bi-Fuel vehicles for the 1999 through 2003 Bi-Fuel CNG model years and 2000 through 2003 Bi-Fuel LPG model years. Refer to the Ford Truck/Car Workshop Manual Section 303-04D.
NOTE: ONCE THE SYSTEM IS DISCONNECTED, COVER ALL OPEN HOSE FITTINGS AND ELECTRICAL CONNECTIONS TO AVOID CONTAMINATION.
- Ensure that all loose debris is removed from the injector area, to avoid contamination during removal.
- Place the Compuvalve flat on a work bench (with injectors facing up).
NOTE: ENSURE THAT THE BENCH SURFACES ARE CLEAN AND DIRT FREE. BENCHES SHOULD BE COVERED TO AVOID SCRATCHING COMPONENT SURFACES.
REMOVAL OF LOW FLOW INJECTOR ASSEMBLY
|NOTE:||DURING THE REMOVAL OF THE LOW FLOW INJECTORS, CARE SHOULD BE TAKEN TO PREVENT ANY DEBRIS FROM ENTERING THE FUEL FLOW OPENINGS.|
- Carefully cut cable tie (1) securing the Low Flow Injector Assembly (A) harness and discard cable tie (Figure 1).
- Remove the two mounting screws (2) securing the Injector Fuel Rail (3) to the Compuvalve (4) and discard screws (Figure 1).
- Remove the Low Flow Injector Assembly (A) and Injector Fuel Rail (3) from Compuvalve (4). Discard Low Flow Injector assembly (A) and set aside the Injector Fuel Rail (3) (Figure 1).
- Remove O-ring (5) from Compuvalve (4) and discard O-ring (Figure 1).
NOTE: IF THE COMPUVALVE IS LEFT UNINSTALLED FOR AN EXTENDED PERIOD OF TIME, USE A CLEAN LINT-FREE CLOTH TO COVER ALL EXPOSED OPENINGS TO AVOID CONTAMINATION.
INSTALLATION OF LOW FLOW INJECTOR ASSEMBLY
- Ensure all mating surfaces between Compuvalve (4), Injector Fuel Rail (3) and Low Flow Injectors (6) & (7) are clean (Figure 1).
NOTE: TO CLEAN, GENTLY WIPE SURFACES USING A CLEAN LINT-FREE CLOTH.
- Ensure that lubricant is on both the inlet and outlet O-rings of the new Low Flow Injectors (6) & (7) and on O-ring (5) (Figure 1).
NOTE: IF REQUIRED, APPLY A THIN FILM OF NON-SILICONE BASED LUBRICANT FOR O-RINGS (E.G. PARKER O-LUBE).
- Before installing the Low Flow Injector Assembly (A), ensure that the orientation of injector #1 (6) (with shorter wire) and of injector #2 (7) (with longer wire) are positioned as shown (Figure 1).
|NOTE:||DURING THE INSTALLATION OF THE LOW FLOW INJECTORS, CARE SHOULD BE TAKEN TO PREVENT ANY DEBRIS FROM ENTERING THE FUEL FLOW OPENINGS.|
- Press the outlet of the Low Flow Injectors (6) & (7) into Compuvalve (4) (Figure 1).
- Route wires under the outlet portion of the Low Flow Injectors (6) & (7) so that the wires will not become pinched between Compuvalve (4) and the Injector Fuel Rail (3) (Figure 1).
- Install O-ring (5) into Compuvalve (4) as shown (Figure 1).
- Press Injector Fuel Rail (3) onto the inlet of Low Flow Injectors (6) & (7) (Figure 1).
- Apply Loctite 272 to the threads of mounting screws (2) (Figure 1).
- Line up the two holes in the Injector Fuel Rail (3) with the mounting holes in the Compuvalve (4) and install with mounting screws (2). Torque to 2-2.5 N-m (18-22 Lb-in) (Figure 1).
CAUTION: ENSURE THAT INJECTOR WIRES ARE NOT PINCHED UNDER INJECTORS OR INJECTOR FUEL RAIL.
- Insert cable tie (1) through the cable tie holder (8) and gently tighten Low flow Injector Assembly (A) harness (Figure 1).
- When complete, install Compuvalve (4) to the vehicle and leak test all removed components and fittings. Refer to Service Manual GFIP162 for the 1996 CNG Bi-Fuel model year and Service Manual GFIP173 for the 1998 CNG Bi-Fuel model year. For Bi-Fuel vehicles for the 1999 through 2003 CNG Bi-Fuel model years and 2000 through 2003 LPG Bi-Fuel model years, refer to Workshop Manual Section 310-00C.
|PART NUMBER||PART NAME|
|2L3Z-9H529-AA||Kit – Low Flow Injector|
OTHER APPLICABLE ARTICLES:
206000, 601300, 602300, 603300, 607000, 607400, 608000, 609000, 609400, 611000, 611500
Figure 1 – Article 03-10-3
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle.
Copyright © 2003 Ford Motor Company