Technical Service Bulletins
|Publication Date: May 5, 2003|
|2000-2003 E-350, E-450, EXCURSION, SUPER DUTY F SERIES|
Some F250-F550 Super Duty and Excursion vehicles equipped with a 5.4L or 6.8L engine, and some E350/450 vehicles equipped with a 6.8L engine may exhibit a rough idle and/or hesitation when accelerating. This may occur intermittently within the first 2-3 minutes after start when engine is not warmed up (ie., conditions other than hot restart). The condition is more likely to occur at ambient temperatures of approximately 60° F (16° C) and higher, and may be aggravated by an unmetered air leak or exhaust leak.
This article must be followed as specified to effectively correct symptoms. Read the article completely before starting service. Refer to the following Service Procedure for details.
F250-F550 Super Duty and Excursion
Service any unmetered air leak, exhaust leak, wiring or other related concern. Replace both front HO2S sensors with the part number listed in this article.
Refer to the E-Series Only PCM Calibration Chart. Do not perform this TSB if the vehicle’s calibration is not listed in the chart. Service any unmetered air leak, exhaust leak, wiring or other related concern. Replace both front HO2S sensors with the part number listed in this article.
- Refer to the following PCM Calibration Chart FOR E-SERIES ONLY to verify that vehicle is addressed by this TSB. Do not perform this TSB on an E-Series vehicle if the calibration is not listed in the E-Series Only PCM Calibration Chart.
E-SERIES ONLY PCM CALIBRATION CHART Application Calibration Part Number (-12A650-) Tear Tag 2000 E450 6.8L 50S 0E418N0511 YC2F-AAE MXK4 2000 E350 6.8L Fed 0E418P0A11 YC2F-ABE CIS4 2001 E450 6.8L 50S 1E418N0510 1C2F-VC NJE2 2001 E350 6.8L Fed 1E418P0A10 1C2F-XC SZZ2 2002 E450 6.8L 50S 2E418N0511 2C2A-ABE BWQ4 2002 E350 6.8L Fed 2E418P0A11 2C2A-ACE CGL4 2003 E450 6.8L 50S 3E418N0505 3C2A-JB YMH1 2003 E350 6.8L Fed 3E418P0A05 3C2A-KB VVU1
- Perform thorough diagnostics in accordance with the applicable PC/ED Workshop Manual, and service any issues.
- Replace both front HO2S sensors, with Part Number 3S4Z-9F472-BA.
NOTE: THE NEW HO2S CONNECTOR (BLACK) REQUIRES THAT THE CLOCKING TAB LOCATED AT THE 4:00 POSITION BE REMOVED. REFER TO FIGURE 1 FOR REQUIRED ELECTRICAL CONNECTOR MODIFICATION FOR MATING WITH VEHICLE WIRING HARNESS. FOLLOWING THE MODIFICATION, VERIFY THAT CONNECTOR MATES FULLY AND LOCKING FEATURE IS ENGAGED. THE ELECTRICAL CONNECTOR HARD-SHELL COLOR OF THE NEW HO2S SENSORS WILL BE BLACK INSTEAD OF GREEN.
Obtain an Authorized Modifications Decal (FPS 8262 – obtainable through DOES II, 25/pkg) and list the date, dealer number, and summary of modifications performed. Select a prominent place adjacent to the Vehicle Emission Control Information Decal suitable for installing the Authorized Modifications Decal. Clean the area, install the decal, and cover it with a clear plastic decal shield.
AUTHORIZED MODIFICATIONS THE FOLLOWING MODIFICATIONS HAVE BEEN MADE: Updated with 3S4Z-9F472-BA Front HO2S sensors per TSB 03-9-11 THESE MODIFICATIONS HAVE BEEN APPROVED, AS APPROPRIATE, BY EPA AND CARB. DEALER NUMBER:——————————————DATE:
FPS 8262 9/78 FORD MOTOR COMPANY PRINTED IN U.S.A.
|PART NUMBER||PART NAME|
|3S4Z-9F472-BA||Oxygen Sensor (HO2S)|
OTHER APPLICABLE ARTICLES:
608000, 608400, 608500, 609000, 609400, 609500, 611000, 611500, 698298
Figure 1 – Article 03-9-11