Technical Service Bulletins
|Publication Date: May 13, 2003|
1998-1999 E SERIES
Article 01-23-1 is being republished in its entirety to update the model years and to update the Service Procedure to replace the Low Flow Injectors and not the Compuvalve assembly.
Due to possible regional Fuel Quality issues in some areas, it may be necessary to clean the low flow injectors in the Compuvalve, and the associated fuel introduction hardware between the Compuvalve and intake manifold (fuel rails, injector sleeves). Typical symptoms of contamination in the low flow injectors are:
- Rough run in Alt fuel mode most noticeable at idle, runs OK in gasoline mode
- No start (green light on) when vehicle is cold in Alt fuel mode, but will start if vehicle has been previously warmed up in gasoline mode
- No start in Alt fuel mode (with green light on) at any time, but starts in gasoline mode.
Verify condition. If normal diagnostics cannot pinpoint the condition, clean the Low Flow CNG injectors in the Compuvalve. Refer to the following Service Procedure for details.
|NOTE:||THIS SERVICE PROCEDURE SHOULD ONLY BE PERFORMED BY AN AUTHORIZED CNG FUEL SYSTEM TECHNICIAN.|
|NOTE:||FOLLOW ALL CNG FUEL SYSTEM SAFETY PROCEDURES LISTED IN THE APPROPRIATE WORKSHOP MANUAL.|
- Set fuel selector switch to Alt position.
- If the vehicle cannot be started in Alt fuel mode, the low flow injectors may be completely stuck closed. If this is the case, attempt to free them by applying 12 Volts directly to the injector coil:
- Disconnect the low flow injector harness (J14).
- Apply battery voltage to pins A and D (marked on the side of the connector) to open injector #1. Listen for an audible click to confirm that the injector has opened.
NOTE: THE INJECTORS ARE NOT DESIGNED TO HAVE A CONTINUOUS 12 V SUPPLY (NORMAL OPERATION IS ABOUT 1.5 V). PROLONGED EXPOSURE TO 12 V WILL CAUSE PERMANENT DAMAGE, SO LIMIT THE 12 VOLTS TO A MAXIMUM OF 5 SECONDS.
- If no click is heard, try several more times, always for 5 seconds or less (wait at least 5 seconds between application of voltage).
- Repeat the above step for injector #2 applying voltage to pins B and D. If vehicle can be started continue to Step 3.
- If the vehicle can still not be started after this procedure, replace the Low Flow Injector assembly.
- Leak check only the connections removed.
- Restart engine, verify the problem has been corrected. Return vehicle.
- Start and run engine to a minimum temperature of 75° C (165° F) (MST or ECT depending on vehicle model year) to ensure engine stability.
- Shut off AC and Defrost.
- Disconnect the electrical connection to the CNG tank valve and run the engine until it auto switches to gasoline.
- Following procedure in GFI Service Manual, bleed off residual CNG line pressure.
- Remove coalescent filter body and drain any contaminants. Wipe the inside with a clean cloth.
- Fill to within 1/4 inch of the top with isopropyl alcohol with coalescent filter in place (alcohol must be at least 90% by volume).
- Re-install coalescent filter body (ensure filter element is still in place).
- Torque for Filter Body: 40 ± 6 N-m (30 ± 5 Lb-ft)
- Torque for Drain Plug: 10 ± 3 N-m (8 ± 2 Lb-ft)
CAUTION: ENSURE THAT ANY LINES THAT WERE DISCONNECTED IN STEP “F” ARE RE-CONNECTED.
- Re-connect the CNG tank valve harness.
- Key on, check for leaks at the coalescent filter housing.
- Start and run vehicle.
- Hook up NGS and monitor RPM.
- Increase the RPM to between 1150 and 1300, maintain this RPM.
- Note time, run for 15 minutes.
- After 15 minutes, shut off engine.
- Restart engine, verify the problem has been corrected, if it has not been resolved, repeat the procedure.
OTHER APPLICABLE ARTICLES:
602300, 603300, 607000, 607400, 607500, 608000, 608400, 608500, 609000, 609400, 609500, 610000, 610500, 611000, 611500, 612000, 612500, 614000, 614500, 698298
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle.
Copyright © 2003 Ford Motor Company