Technical Service Bulletins
|Publication Date: July 1, 2011|
Some 2011 F-150 vehicles equipped with a 5.0L engine and air conditioning (A/C) compressor stretchy belt configuration built on or before 2/14/2011 may exhibit a light lower end engine knock most noticeable when engine temperature is warm and the vehicle is at idle.
Refer to the Service Procedure to correct the condition.
- Remove the front end accessory drive (FEAD) and A/C compressor stretchy belt. Refer to Workshop Manual (WSM), Section 303-05 Removal and Installation Air Conditioning (A/C) compressor belt – 3.5L GTDI, 3.7L, 5.0L. Does the knocking noise remain?
- Yes, the knocking noise remains after removing the A/C stretchy belt. Do not continue with this article. Refer to WSM, Section 303-00 for further diagnosis
- No, the noise is no longer present. Obtain the Drive Belt Kit proceed to Step 2.
- Remove the FEAD belt tensioner and bolt from the engine front cover. Refer to WSM, Section 303-05 – Exploded view.
- Remove and discard existing A/C compressor to condenser discharge line and install new A/C compressor to condenser discharge line supplied in the Drive Belt Kit. Refer to WSM, Section 412-01.
- Using a 8 X 1.25mm tap, clean the mounting locations noted on the engine front cover and use compressed shop air to clean any remaining debris. (Figure 1)
Figure 1 – Article 11-7-1
- Install A/C compressor drive belt idler pulley and A/C compressor drive belt idler pulley bolt supplied in the drive belt kit onto the engine front cover top mounting location. Tighten to 25 N-m (18 lb-ft).
- Install A/C drive compressor belt tensioner supplied in the drive belt kit onto the engine front cover lower mounting location. Tighten to 25 N-m 18 lb-ft).
- Install new A/C compressor belt supplied in the drive belt kit. Refer to WSM, Section 303-05 R and A/C compressor belt – 3.5L GTDI, 3.7L, 5.0L referring to the 5.0L (4V) late build vehicles procedure for proper belt routing. (Figure 2)
Figure 2 – Article 11-7-1
- Reinstall the FEAD belt tensioner and bolt onto the engine front cover. Tighten to 25 N-m(18 lb-ft). Refer to WSM, Section 303-05 FEAD – Exploded view 5.0L (4V) late build vehicles.
- Reinstall the FEAD belt. Refer to WSM, Section 303-05 FEAD – Exploded view 5.0L (4V) late build vehicles.
- Install Integrated Diagnostic System (IDS) and identify the vehicle. Answer the IDS screen prompts according to the current vehicle A/C belt configuration.
- Reprogram the Powertrain Control Module (PCM) using IDS release 72.03 or later. This new calibration is not included in the VCM 2011.3 DVD. Calibration files may also be obtained at www.motorcraft.com.
- Perform misfire monitor neutral profile correction. Select IDS toolbox icon, Powertrain, Service Functions, then Misfire Monitor Neutral Profile Correction.
NOTE: PLEASE ADVISE THE CUSTOMER THAT THIS VEHICLE IS EQUIPPED WITH AN ADAPTIVE TRANSMISSION SHIFT STRATEGY WHICH ALLOWS THE VEHICLE'S COMPUTER TO LEARN THE TRANSMISSION'S UNIQUE PARAMETERS AND IMPROVE SHIFT QUALITY. WHEN THE ADAPTIVE STRATEGY IS RESET, THE COMPUTER WILL BEGIN A RE-LEARNING PROCESS. THIS RE-LEARNING PROCESS MAY RESULT IN FIRMER THAN NORMAL UPSHIFTS AND DOWNSHIFTS FOR SEVERAL DAYS.
|PART NUMBER||PART NAME|
|BL3Z-8620-E||Drive Belt Kit|
Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
|110701A||F-150 5.0L: Install Service Kit, Includes Time To Recover, Evacuate And Charge A/C (Do Not Use With Any Other Labor Operations)||1.2 Hrs.|
|BASIC PART NO.||CONDITION CODE|
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a condition described affects your car or truck. Contact a Ford or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources.
Copyright ï¿½ 2011 Ford Motor Company