Ford Truck Enthusiasts Forums - Search Results



Showing results 1 to 15 of 498
Search took 0.48 seconds.
Search: Posts Made By: Spktyr
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 12-05-2016, 01:00 AM
Replies: 4
Views: 181
Posted By Spktyr
Hm. That doesn't seem too bad. Can you point me...

Hm. That doesn't seem too bad. Can you point me at some dyno sheets for this setup?
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 12-05-2016, 12:59 AM
Replies: 4
Views: 181
Posted By Spktyr
That was a thought, but a short version of the...

That was a thought, but a short version of the salient points for me:

1. I have a number of friends who are Fox-Body 5.0 Mustang guys. They have lots of 5.0 parts I can get ahold of from them for...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 11-29-2016, 05:10 AM
Replies: 4
Views: 181
Posted By Spktyr
Considering 5.0 Build

I have a 1989 Bronco with an EFI 302/5.0. I am considering replacing the engine with a GT40 5.0 out of an Explorer and using MegaSquirt EFI to control it. Since I'd be doing that, it seems like it...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 11-07-2016, 12:52 AM
Replies: 2
Views: 149
Posted By Spktyr
9th gen Diesel radiator core support/crossmember interchange?

Asked a similar question over on the OBS PSD sub forum, asking over here as well as it applies to both areas. Hope that's not a problem.

I had someone ask me a question that I didn't know the ...
Forum: 1994.5 - 1997 7.3L Power Stroke Diesel 11-07-2016, 12:46 AM
Replies: 1
Views: 121
Posted By Spktyr
Radiator core support or crossmember interchange question

Hello all - had someone ask me a question that I didn't know the answer to and didn't find in the archives. We know the 9th gen F-truck PSD radiator crossmember seems to be impossible to find new and...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 09-22-2016, 08:15 AM
Replies: 4
Views: 253
Posted By Spktyr
Anyone have any ideas?

Anyone have any ideas?
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 09-20-2016, 05:44 PM
Replies: 2
Views: 169
Posted By Spktyr
Check your pulley and accessory drive bearings on...

Check your pulley and accessory drive bearings on the belt-driven stuff at the front of the motor first. Failing bearings can howl.
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 09-20-2016, 05:59 AM
Replies: 4
Views: 253
Posted By Spktyr
351W Engine Wiring Harness Interchange?

Trying to help a local guy with a 91 Bronco 351W/5.8L. His engine wiring harness was chewed through by rodents and then 'repaired' by someone who didn't know what they were doing. The nature of the...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 09-20-2016, 05:48 AM
Replies: 8
Views: 405
Posted By Spktyr
Just to close this for the archives, the hitching...

Just to close this for the archives, the hitching problem turned out to be the low pressure fuel pump in the tank.
Forum: 1978 - 1996 Big Bronco 05-26-2016, 04:38 PM
Replies: 1
Views: 227
Posted By Spktyr
Rear bumper compatibility?

I seem to remember that there's some sort of compatibility issue between the Bronco and similar year Ford F-150s, but I don't remember what it is. Can someone check me on that, or am I remembering...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-22-2016, 03:26 AM
Replies: 7
Views: 226
Posted By Spktyr
Following up here - the 21mm did it and we were...

Following up here - the 21mm did it and we were easily able to remove the axle. Well, all except the last U-bolt, which resisted the impact and had to be turned by breaker bar a little at a time all...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-17-2016, 08:03 PM
Replies: 7
Views: 226
Posted By Spktyr
Angle grinders, torches or any powered cutting...

Angle grinders, torches or any powered cutting device is prohibited at this junkyard after idiots ruined it for everyone. Otherwise, this wouldn't even be a question.

I'm in Texas, most of the...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-17-2016, 09:14 AM
Replies: 7
Views: 226
Posted By Spktyr
Yeah, that should be the same - thanks for...

Yeah, that should be the same - thanks for looking.

It doesn't have the same ratio as the front, but he's planning on re-gearing the truck this fall anyway, when money should be far less tight -...
Forum: 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks 05-17-2016, 08:18 AM
Replies: 7
Views: 226
Posted By Spktyr
82 Axle Fastener Sizes?

My friend's 84 Bronco rather decisively lunched its 8.8 rear axle. Rather than spend money repairing the 8.8, we decided to get a 9" from another truck. We've found a donor (82 F-150) and a...
Forum: 1987 - 1996 F150 & Larger F-Series Trucks 04-21-2016, 05:44 PM
Replies: 2
Views: 202
Posted By Spktyr
95 F-350 Front Body Mount Bolt Head Size?

Quick question - what size is the bolt head on the 95 F-350's front body mounts? Or, in other words, what size socket(s) or wrench(es) would I need to loosen it? I'm looking to help someone out with...
Showing results 1 to 15 of 498

 
Forum Jump

All times are GMT -5. The time now is 05:14 PM.


This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.