Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 280
Search took 0.25 seconds.
Search: Posts Made By: Steves55
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-16-2016, 08:47 PM
Replies: 6
Views: 159
Posted By Steves55
Thanks. Yes, it uses a set screw.

Thanks. Yes, it uses a set screw.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-16-2016, 08:05 AM
Replies: 6
Views: 159
Posted By Steves55
Air Cleaner to fit Holley 1904

Hello all. I have a nice Edmunds Air Cleaner made to fit a 2 barrel carburetor and would like to know if anyone knows how I could possibly make this fit my Holley 1904 1 barrel carb neck? Many...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-08-2016, 11:37 AM
Replies: 13
Views: 562
Posted By Steves55
Although the positive & negative cables from my...

Although the positive & negative cables from my battery...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-02-2016, 12:34 PM
Replies: 13
Views: 562
Posted By Steves55
Right now, my battery is grounded to the frame;...

Right now, my battery is grounded to the frame; would it be better if it was grounded to the engine or does it matter? I do have a cable running from my starter mounting bolt to the ground post of...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-01-2016, 08:00 PM
Replies: 13
Views: 562
Posted By Steves55
To the best of my knowledge, the trans to...

To the best of my knowledge, the trans to firewall ground is the correct stock set-up. I am trying to visualize that 3 post terminal block-do you have a photo or describe where it's located? I am...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-01-2016, 07:16 PM
Replies: 13
Views: 562
Posted By Steves55
6 Volt Grounding Points

On my 55 (6-v pos ground), I have a grounds located:
1. Battery grounded to frame.
2. A ground cable from starter mount bolt to battery ground post (which is grounded to frame).
3. Braided ground...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-01-2016, 07:09 PM
Replies: 3
Views: 288
Posted By Steves55
Thanks guys. I got a heavy duty switch with a...

Thanks guys. I got a heavy duty switch with a fuse and I am good-to-go.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-28-2016, 07:13 PM
Replies: 3
Views: 288
Posted By Steves55
Fog Light Wiring Question

I am installing a single fog light on my 55 F-100 and am having a brain dump! Should the in-line fuse run between the fog light and switch or between the battery and switch or does it matter? I am...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 12-19-2015, 09:04 AM
Replies: 4
Views: 606
Posted By Steves55
Electric Fuel Pump Location

I am wanting to install an Airtex low pressure electric fuel pump to use whenever my 223 six sometimes get the vapor lock hiccups. Since my tank is mounted under the running board, there is not much...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-27-2015, 06:14 PM
Replies: 28
Views: 1,021
Posted By Steves55
Chris, I'm not very familiar with the Flathead 6...

Chris, I'm not very familiar with the Flathead 6 but it looks like C & G early Ford carries them. Give them a call to double check. Very nice folks as well! With regards to sealant, you may not...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 09-07-2015, 04:51 PM
Replies: 27
Views: 1,651
Posted By Steves55
Are they the Jeffrey Allen Visors? I see them on...

Are they the Jeffrey Allen Visors? I see them on E-Bay.
7" Outer Mounted Head Lamp Light Trim Visor Jeffrey Allen Style Custom Car Truck | eBay
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-20-2015, 06:36 AM
Replies: 5
Views: 547
Posted By Steves55
My apologies for a question that would be tough...

My apologies for a question that would be tough to offer advice without seeing it. Anyhow, just to play it safe, I went ahead and removed the hoses, raised the front of the engine to provide enough...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 08-17-2015, 05:46 AM
Replies: 5
Views: 547
Posted By Steves55
223 Six Motor Mount

This evening I will be changing the front motor mount on my 223 six. From those who have have done this, did you drain the coolant and remove the lower radiator hose before slightly rasing the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-20-2015, 06:05 PM
Replies: 28
Views: 1,021
Posted By Steves55
Thanks Ross.

Thanks Ross.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-19-2015, 06:33 AM
Replies: 28
Views: 1,021
Posted By Steves55
One more question; for reinstallation on the 223...

One more question; for reinstallation on the 223 I6, my shop manual does not specify which order if the gasket is installed first on the block followed by the stat prior to bolting up the housing...
Showing results 1 to 15 of 280

 
Forum Jump
 


All times are GMT -5. The time now is 11:34 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup