Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 311
Search took 0.20 seconds.
Search: Posts Made By: TheDudeAbides
Forum: '80-'86 HOWTO's 06-18-2015, 03:29 PM
Replies: 70
Views: 21,072
Posted By TheDudeAbides
thank you kindly sir. i'm going to order lights...

thank you kindly sir. i'm going to order lights and flashers today. gotta cut out some tabs on the plasma table for fuel filler necks as well. its slow going but i'll get it all buttoned up....
Forum: '80-'86 HOWTO's 06-17-2015, 08:57 PM
Replies: 70
Views: 21,072
Posted By TheDudeAbides
i have read about the bulb swaps and done a few...

i have read about the bulb swaps and done a few of my own on previous vehicles. i'm building a stakeside flatbed for my 85 f150. i will be installing some 6.5" LED oval brake/turn lights w/ 3 wire...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 05-27-2015, 09:09 PM
Replies: 5
Views: 476
Posted By TheDudeAbides
indeed, go big or go home.

indeed, go big or go home.
Forum: Ford Inline Six, 200, 250, 4.9L / 300 05-11-2015, 12:20 AM
Replies: 5
Views: 1,576
Posted By TheDudeAbides
hope the image helps. no offense intended, but...

hope the image helps. no offense intended, but for the work required, and simplicity gained...i'd personally opt for a DS2 swap. parts would probably be cheaper in the long run as well. hope you get...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 05-11-2015, 12:17 AM
Replies: 5
Views: 1,576
Posted By TheDudeAbides
http://repairguide.autozone.com/znetrgs/repair_gui...

http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/07/7d/4d/large/0900c15280077d4d.gif
Forum: Ford Inline Six, 200, 250, 4.9L / 300 05-08-2015, 10:22 PM
Replies: 3
Views: 637
Posted By TheDudeAbides
pretty sure i have one sitting on a shelf in the...

pretty sure i have one sitting on a shelf in the shop. if i still have it out there, pay the shipping and its yours if you like.
Forum: 4 Cylinder Engines 05-06-2015, 09:55 AM
Replies: 5
Views: 1,022
Posted By TheDudeAbides
anything can be done...bottom line. it all...

anything can be done...bottom line. it all depends on how deep your pockets are, and how much time you can spare. i'd start by getting some dimensions between the two blocks. determine bore spacing,...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 05-06-2015, 09:46 AM
Replies: 18
Views: 1,042
Posted By TheDudeAbides
this is turning into quite the helpful bit of...

this is turning into quite the helpful bit of info.

didn't quite understand the "redneck mod" on the P/S pump though. with a given volume exchange at a relatively constant rate...enlarging the...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 04-29-2015, 10:50 AM
Replies: 11
Views: 848
Posted By TheDudeAbides
1) i chose to edit the post and omit the info...

1) i chose to edit the post and omit the info myself cause i didnt feel that my job description was nearly as valid as the guidance being given. you're right though, i'm not a very popular guy in...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 04-28-2015, 12:18 PM
Replies: 11
Views: 848
Posted By TheDudeAbides
all of these are very valid points to be made....

all of these are very valid points to be made. like its been said, take your time, keep things plenty clean, practice on some scrap first. good penetration and sound quality welds are perfectly...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 04-28-2015, 12:11 PM
Replies: 12
Views: 1,025
Posted By TheDudeAbides
As far as height, i don't believe there is any...

As far as height, i don't believe there is any difference. the internal baffle of the cover is located different on the later model valve covers though. it had to be reconfigured for the pedestal...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 04-23-2015, 01:11 AM
Replies: 108
Views: 15,499
Posted By TheDudeAbides
looks like a quality piece, plus the longevity...

looks like a quality piece, plus the longevity and bling factor of stainless. its good that he's making them available for folks that either cant or would rather not try welding one up. uff da...
Forum: Ford Inline Six, 200, 250, 4.9L / 300 03-24-2015, 02:04 AM
Replies: 108
Views: 15,499
Posted By TheDudeAbides
i've got about a dozen plates burned out here at...

i've got about a dozen plates burned out here at the house. shoot me a PM if interested.
Forum: WTB - Parts & other 03-20-2015, 10:03 AM
Replies: 10
Views: 360
Posted By TheDudeAbides
update...after picking up the ds2 setup, it works...

update...after picking up the ds2 setup, it works pretty well. working on dialing in a good curve on a dizzy i rebuilt, then i plan on doing an HEI module/TFI coil swap. i'll be able to buy cheaper...
Forum: WTB - Parts & other 03-20-2015, 09:59 AM
Replies: 10
Views: 360
Posted By TheDudeAbides
do you remember what size it is? i do have one...

do you remember what size it is? i do have one that i'm going to use, but spare parts are always handy.
Showing results 1 to 15 of 311

 
Forum Jump
 


All times are GMT -5. The time now is 03:30 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup