Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 308
Search took 0.19 seconds.
Search: Posts Made By: Hotrod70d
Forum: Super Duty & Heavy Duty 06-16-2016, 07:30 PM
Replies: 6
Views: 384
Posted By Hotrod70d
May need to post some pics

May need to post some pics
Forum: Super Duty & Heavy Duty 05-15-2016, 09:03 AM
Replies: 17
Views: 872
Posted By Hotrod70d
I have cooper at3 on my truck, the wear is even....

I have cooper at3 on my truck, the wear is even. Doubt I'll get much more than 20k out of the tread, most likely won't buy again too expensive too only get 20k out of them .gonna buy cheap tires next...
Forum: Super Duty & Heavy Duty 04-10-2016, 12:27 PM
Replies: 8
Views: 386
Posted By Hotrod70d
My 325 18 s. Rubbed before and after the 2.5 lift...

My 325 18 s. Rubbed before and after the 2.5 lift with stock tires , they rubbed at full lock too the left, offset rims will take care of it. I doubt that it's too the left, if your gonna spend a few...
Forum: Super Duty & Heavy Duty 04-08-2016, 12:08 PM
Replies: 6
Views: 2,054
Posted By Hotrod70d
325 are the metric version of. 35x12.5. 295 70...

325 are the metric version of. 35x12.5. 295 70 is the the same as a 35x11. The 325 will fit stock on new trucks minor rub at full lock stock rims to the left. They even rub on stock wheels with...
Forum: Super Duty & Heavy Duty 04-07-2016, 07:13 PM
Replies: 4
Views: 305
Posted By Hotrod70d
Bought mine on eBay about 150 with the switch...

Bought mine on eBay about 150 with the switch harness lights and buckets. Was a half hr install.
Forum: Super Duty & Heavy Duty 04-02-2016, 07:59 AM
Replies: 11
Views: 972
Posted By Hotrod70d
Have a ready lift 2.5 sst with a 5" rear block,...

Have a ready lift 2.5 sst with a 5" rear block, nice lift for 325 , couldn't go any more with gooseneck trailer.
Forum: Super Duty & Heavy Duty 03-12-2016, 07:09 AM
Replies: 3
Views: 253
Posted By Hotrod70d
Watch the ready lift video on YouTube. Too see if...

Watch the ready lift video on YouTube. Too see if something else could be wrong
Forum: Super Duty & Heavy Duty 03-12-2016, 07:08 AM
Replies: 3
Views: 253
Posted By Hotrod70d
Did you put front shock extensions on? Did you...

Did you put front shock extensions on? Did you put front sway bar drop brackets on? Track bar drop bracket? Flip brake lines at junction block? Any of these could factor in with a incomplete kit and...
Forum: 6.2L V8 02-28-2016, 08:31 PM
Replies: 9
Views: 1,145
Posted By Hotrod70d
The exhaust hits the front drive shaft, people on...

The exhaust hits the front drive shaft, people on have modified the exhaust , heat and bend , cut and replace , it has been done . They say not much rubbing so I'm guessing it could be heated and...
Forum: Super Duty & Heavy Duty 02-28-2016, 08:24 PM
Replies: 6
Views: 1,341
Posted By Hotrod70d
Id say buy the kit . Plus you will have all the...

Id say buy the kit . Plus you will have all the right parts, 37 will work with the correct offset on your rims.
Forum: Super Duty & Heavy Duty 02-27-2016, 01:52 PM
Replies: 18
Views: 2,989
Posted By Hotrod70d
When u look at the front wheels from the side and...

When u look at the front wheels from the side and u draw cross hairs over the tire this is where it starts , now roll the front wheel on a pivot from the back torsion bar like u would on putting a...
Forum: Super Duty & Heavy Duty 02-22-2016, 06:45 PM
Replies: 84
Views: 3,842
Posted By Hotrod70d
Ford did take bail out money they just repaid it...

Ford did take bail out money they just repaid it unlike a couple other companies
Forum: Super Duty & Heavy Duty 02-22-2016, 06:43 PM
Replies: 19
Views: 1,408
Posted By Hotrod70d
Either put the factory rear 4 inch block under it...

Either put the factory rear 4 inch block under it or get a ready lift 5 inch block for rear. I have the 5 inch one sits slightly higher in rear with the 2.5 front lift
Forum: Super Duty & Heavy Duty 02-14-2016, 01:30 PM
Replies: 28
Views: 960
Posted By Hotrod70d
They are correct early superdutys had 4 inch...

They are correct early superdutys had 4 inch rear blocks had a heavy rake . they corrected it and used the factory 2 inch block a few yrs later. I'd raise the front my self . They look better. And...
Forum: Super Duty & Heavy Duty 02-13-2016, 06:48 PM
Replies: 3
Views: 325
Posted By Hotrod70d
35" fit stock . I have ready lift 2.5 " with the...

35" fit stock . I have ready lift 2.5 " with the 5 " block. Has all parts needed to drops way bar, pan bar, drive shaft shim. Etc paid 325 for the kit.
Showing results 1 to 15 of 308

 
Forum Jump
 


All times are GMT -5. The time now is 05:49 PM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup