Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 500
Search took 0.20 seconds.
Search: Posts Made By: yetiman38237
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 04-13-2016, 03:32 PM
Replies: 6
Views: 219
Posted By yetiman38237
First, take it and get an alignment done. That...

First, take it and get an alignment done. That will keep it from being a Nascar truck, then, you can adjust your steering wheel if need be. Nice thing about these old Fords is you have a lot of...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 04-13-2016, 03:27 PM
Replies: 17
Views: 605
Posted By yetiman38237
Torch in engine compartment = fun fun fun. I did...

Torch in engine compartment = fun fun fun. I did as Freightrain, even went as far as to use stainless hardware and didn't leak there. Best thing I ever did was replace heads and go with...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 03-01-2016, 02:44 PM
Replies: 17
Views: 666
Posted By yetiman38237
Agreed, I replaced kingpins when I installed the...

Agreed, I replaced kingpins when I installed the disc brakes and they had been in there for years. The bushings were plastic and still in decent shape. Not as good as bronze by any means but should...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 02-25-2016, 01:17 PM
Replies: 28
Views: 738
Posted By yetiman38237
I'm guessing you could shorten the shaft? Not...

I'm guessing you could shorten the shaft? Not sure how well it would align up though. Seems like there ought to be a simple solution out there. I never found it and ended up just going with an...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 02-22-2016, 04:15 PM
Replies: 28
Views: 738
Posted By yetiman38237
Don't know how you would find (affordable)...

Don't know how you would find (affordable) pulleys brackets etc without a pick and pull option
Forum: Kentucky Chapter 02-03-2016, 02:32 PM
Replies: 35
Views: 1,550
Posted By yetiman38237
like the 250 yard range idea :D

like the 250 yard range idea :D
Forum: FE & FT Big Block V8 (332, 352, 360, 390, 406, 410, 427, 428) 01-25-2016, 07:19 PM
Replies: 9
Views: 927
Posted By yetiman38237
Did you have a chat with the fine folks at HF? ...

Did you have a chat with the fine folks at HF? Man that will ruin your day and possibly more!
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-25-2016, 07:11 PM
Replies: 14
Views: 334
Posted By yetiman38237
Mine bounces and it is a brand new cable.......

Mine bounces and it is a brand new cable.......
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-21-2016, 01:00 PM
Replies: 13
Views: 675
Posted By yetiman38237
I used sealer in the seam on bedside.....was...

I used sealer in the seam on bedside.....was always filling with water and collecting with dirt to form problems. I still have the seam just not as deep now. If you get some on area you don't want...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-20-2016, 02:16 PM
Replies: 11
Views: 459
Posted By yetiman38237
Mine is held in place with a plastic ring with a...

Mine is held in place with a plastic ring with a pop out tab, looks kinda like a wire tie.
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-18-2016, 02:49 PM
Replies: 113
Views: 4,644
Posted By yetiman38237
I remember seeing a canary yellow F100 at the 1/8...

I remember seeing a canary yellow F100 at the 1/8 mile track where I used to run. He had that truck hooking up big time. Don't remember what he ran but it would tote the tires out of the hole. ...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-18-2016, 02:34 PM
Replies: 19
Views: 442
Posted By yetiman38237
So small they are hard to cook on.......:D

So small they are hard to cook on.......:D
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-18-2016, 02:30 PM
Replies: 10
Views: 411
Posted By yetiman38237
They will probably be warped a little on the...

They will probably be warped a little on the edges making it more difficult to get a good seal. Set them on a 2 x 4 and use a rubber mallet and tap the edges back straight. I always use fel-pro...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-18-2016, 02:02 PM
Replies: 3
Views: 257
Posted By yetiman38237
I know regular paint will bake off the heads...

I know regular paint will bake off the heads pretty darn quick. I ended up redoing my heads with enamel and it still looks pretty good. If truck was a daily driver it would be toasted by now. ...
Forum: 1967 - 1972 F-100 & Larger F-Series Trucks 01-18-2016, 01:58 PM
Replies: 10
Views: 411
Posted By yetiman38237
I used to have a cheapo powder coat gun I bought...

I used to have a cheapo powder coat gun I bought from Eastwood. Decided I needed to sell it on eBay and got more than I paid for the kit. Also, dumbest thing I have done in at least 5 years......I...
Showing results 1 to 15 of 500

 
Forum Jump
 


All times are GMT -5. The time now is 04:33 PM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup