Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 500
Search took 0.34 seconds.
Search: Posts Made By: daveengelson
Forum: Garage & Workshop Yesterday, 06:28 PM
Replies: 27
Views: 934
Posted By daveengelson
Greatly appreciate comments!! Appears the bits...

Greatly appreciate comments!! Appears the bits mentioned in the post # 21 cover majority of my concerns, likely pull the trigger on the purchase and restock for future use.

Again, I thank U's all...
Forum: Garage & Workshop Yesterday, 06:01 PM
Replies: 27
Views: 934
Posted By daveengelson
Found the remainder of the bolt broke off and...

Found the remainder of the bolt broke off and uneven so I was unable to set the center punch and consequently the drill had a tendency to wonder. The 1st bit created a great deal of heat but very...
Forum: Garage & Workshop Yesterday, 05:11 PM
Replies: 3
Views: 103
Posted By daveengelson
Purchased the HF $200 cabinet w/ dual doors, and...

Purchased the HF $200 cabinet w/ dual doors, and 20% discount reduced the cost even more; peased with the quality. For large items open a door, taped an engine bag and able to blast the larger items....
Forum: Garage & Workshop Yesterday, 01:28 PM
Replies: 27
Views: 934
Posted By daveengelson
Purchased a set of Dewalt Cobalt bits and seem to...

Purchased a set of Dewalt Cobalt bits and seem to hold up well; although, couple days ago broke a hardened intake manifold bolt off and went thru a couple of the Dewalt bits to drill it out, probly...
Forum: Garage & Workshop Yesterday, 10:46 AM
Replies: 3
Views: 103
Posted By daveengelson
Purchased a HF cabinet with the siphon feed,...

Purchased a HF cabinet with the siphon feed, found reaching the correct balance between air and medium is important. Also, condensation becomes an issue, the gun/nozzle kit came with a 6" long needle...
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 07-25-2016, 11:09 AM
Replies: 4
Views: 165
Posted By daveengelson
Just reconditioned and replaced the vent seals on...

Just reconditioned and replaced the vent seals on my 65, not sure if similar/same; I noticed there is a slight space in the knurled shaft that corresponds with a gap in the serrated washer and when...
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 07-25-2016, 11:00 AM
Replies: 8
Views: 266
Posted By daveengelson
Was going to suggest purchasing set off eBay;...

Was going to suggest purchasing set off eBay; having said that, came out looking mitty fine, much improvement over the plain sheet metal. Good Job!!
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-25-2016, 10:57 AM
Replies: 7
Views: 172
Posted By daveengelson
Thank you for bringing it to my attention....

Thank you for bringing it to my attention. Reviewed couple 'how to' videos on heli coil install, hopefully will not have to go there. Seems it's not that complicated, imagine comes down to drilling,...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-24-2016, 10:22 PM
Replies: 7
Views: 172
Posted By daveengelson
Have not had a change to test the repair, seems...

Have not had a change to test the repair, seems Fed X driver and I have issues, the package has been accumulating travel miles for the past week.

Anyhow, it's going to be close, the die seems to...
Forum: Big Block V8 - 385 Series (6.1/370, 7.0/429, 7.5/460) 07-24-2016, 06:17 PM
Replies: 7
Views: 361
Posted By daveengelson
I tend to not make recommendations; I would check...

I tend to not make recommendations; I would check customer reviews on local engine rebuild shops and inquire. Having said that, purchased a created long block from S&S engine, out of Spokane...
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 07-23-2016, 10:50 AM
Replies: 1
Views: 168
Posted By daveengelson
Topic came up and noted at the bottom of this...

Topic came up and noted at the bottom of this thread: 66F100Again,

In the last post in the thread: Delco 13" blade insert.

http://www.ford-trucks.com/forums/1410704-wiper-blade-refill.html
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 07-20-2016, 04:33 PM
Replies: 20
Views: 653
Posted By daveengelson
Appears member's have thoroughly addressed the...

Appears member's have thoroughly addressed the issue, thought I would toss in couple additional suggestions. If decide to dip the carb suggest suggest remove floats; particularly if brass, or other...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-19-2016, 10:18 AM
Replies: 7
Views: 172
Posted By daveengelson
Greatly appreciate your suggestions! It took...

Greatly appreciate your suggestions!

It took me a nano-second to realize the intake had to come off before trying to make the repair; only required removing a couple hoses and throttle linkage....
Forum: 1961 - 1966 F-100 & Larger F-Series Trucks 07-15-2016, 05:32 PM
Replies: 4
Views: 211
Posted By daveengelson
First and Foremost, Welcome to FTE. Posting a...

First and Foremost, Welcome to FTE. Posting a picture from the 1965 Ford Truck 'wiring diagram manual', pg. 3 Ignition, Starting and Charging.
...
Forum: Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W) 07-15-2016, 02:40 PM
Replies: 7
Views: 172
Posted By daveengelson
Easy-Out

68 289/302; Edelbrook Performer:

Found the source of a water leak, not sure how, but the most forward intake manifold bolt snapped leaving approx. 1/2" in the block. Rather than disassemble and...
Showing results 1 to 15 of 500

 
Forum Jump
 


All times are GMT -5. The time now is 07:00 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup