Ford Truck Enthusiasts Forums - Search Results
 

Go Back   Ford Truck Enthusiasts Forums > Search Forums
Log In 


Showing results 1 to 15 of 500
Search took 0.36 seconds.
Search: Posts Made By: big job
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks Yesterday, 03:22 AM
Replies: 7
Views: 142
Posted By big job
Lets see if I'm on the same page. Couple pumps...

Lets see if I'm on the same page. Couple pumps and you have a good pedal and it
will stay- all day? But after a short rest it now goes to the floor - couple pumps you
have a good pedal. So I see...
Forum: Large Truck 07-20-2016, 02:42 AM
Replies: 61
Views: 15,778
Posted By big job
What we did. The truck is a 49 F7 & we found a...

What we did. The truck is a 49 F7 & we found a box truck and I think' don't
know, but some GMC we bought front and rear axles all big disk's. The
front spindles are just about exactly like the...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 07-17-2016, 03:26 AM
Replies: 5
Views: 131
Posted By big job
Sometimes if one does not know then don't do it. ...

Sometimes if one does not know then don't do it. My case I removed my hopeless
rare double action to find another. So I just put a mini clamp about 1/2 to raise the
push rod so it does nothing....
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-28-2016, 02:25 AM
Replies: 14
Views: 384
Posted By big job
I also agree, the choice he made with the dash...

I also agree, the choice he made with the dash was easier. On the
build we did we still want the original cluster. So the plan is for
the 1997 gauges into a formed housing using the glass &...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-16-2016, 12:59 AM
Replies: 31
Views: 1,760
Posted By big job
We have done several conversion of the above...

We have done several conversion of the above setup which is a direct bolt up.
Problem is you have to relocate the fill hole in the floor under the seat cause the master
cylinder sets back further...
Forum: Large Truck 06-11-2016, 04:08 AM
Replies: 473
Views: 39,698
Posted By big job
Thanks Bill sam

Thanks Bill sam
Forum: Large Truck 06-10-2016, 06:59 AM
Replies: 473
Views: 39,698
Posted By big job
Head diference's

Hi Bill, we have a exhaust port cracked on the head of a 391. We have
in storage & I don't know what it is, but it has a massive 5 speed Spicer trans. I know its not a car 390, it has the big...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-07-2016, 04:38 AM
Replies: 19
Views: 769
Posted By big job
We buy from Cleggs Machine in Utah Nice people to...

We buy from Cleggs Machine in Utah Nice people to deal with roughly little over $800 buys everything all US major mfg. Myself it would be set of pistons main & rod and
defiantly cam bearings & oil...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-07-2016, 04:23 AM
Replies: 6
Views: 298
Posted By big job
Just a matter of choice, nothing wrong with...

Just a matter of choice, nothing wrong with either I prefer the EAB the last ones.
I know a guy 10 min away with a 1990's new complete crate French 239 on the shipping palet. He wants $1500 I'll get...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 06-06-2016, 04:53 AM
Replies: 7
Views: 350
Posted By big job
If this F7 is a standard F7, the magic is, it has...

If this F7 is a standard F7, the magic is, it has hard to find a 5 speed overdrive. 5 direct was an option.
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-21-2016, 12:31 AM
Replies: 11
Views: 318
Posted By big job
Typical varnish buildup. Most will do that, use a...

Typical varnish buildup. Most will do that, use a little brake cleaner. And when
installing new cam bearings make sure the rear bearing hole is dead on with the
block for the fuel pump push rod. ...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 05-18-2016, 03:01 AM
Replies: 22
Views: 885
Posted By big job
Best prices that we use is 'Cleggs Machine'...

Best prices that we use is 'Cleggs Machine' search them, all USA products.
example all gaskets, set of pistons & rings rod & mains melling oil pump
cam bearings all for around $850. Then valve...
Forum: Large Truck 05-07-2016, 05:36 AM
Replies: 2
Views: 233
Posted By big job
I would do a search on "Morse control" or cable. ...

I would do a search on "Morse control" or cable. I bet they were made by Morse in
the first place. Or some one who deals with dump bodies who have many sizes for
cable controls like PTO cables. ...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-21-2016, 04:30 AM
Replies: 9
Views: 403
Posted By big job
They sure are nice. This pic is our first test...

They sure are nice. This pic is our first test on a high capacity test.
'However" you will have to get creative. Ours will lift a F900 but
problem is the truck frame v/s running boards or saddle...
Forum: 1948 - 1956 F1, F100 & Larger F-Series Trucks 04-13-2016, 03:56 AM
Replies: 8
Views: 351
Posted By big job
Although out of high school my first job was a...

Although out of high school my first job was a cable maker at Raytheon. Cables were
massive for ships and submarines. A scale print was actually on the floor with nails
nailed through the print...
Showing results 1 to 15 of 500

 
Forum Jump
 


All times are GMT -5. The time now is 11:35 AM.

 

Advertising - Terms of Use - Privacy Statement - Terms of Service - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup